Mitsubishi Grandis. Manual — part 228
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-374
ROOM LAMP
Inspection Procedure P-1: The interior lamps (room ramp, rear personal lamps, door lamps, luggage
compartment lamp, key illumination lamp) does not illuminate or extinguish normally.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
KEY CYLINDER
ILLUMINATION
LAMP
· ROOM LAMP
· DOOR LAMP
· LUGGAGE
COMPARTMENT
LAMP
· REAR PERSONAL
LAMP
J/B SIDE
ETACS-ECU
FUSIBLE
LINK
26
Interior Lamp Circuit <without keyless entry system>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-375
COMMENTS ON TROUBLE SYMPTOM
The ETACS-ECU activates the interior lamps (room
lamp, rear personal lamp, luggage compartment
lamp, door lamps, key cylinder illumination lamp)
according to the input signals below.
• Ignition switch (IG1)
• Door switches
• Tailgate switch
• Door key switch
• Tailgate key switch
• Driver's door lock actuator
• Interior lamp switch
• Multi-purpose fuse No.18
• Key reminder switch <vehicles with keyless entry
system>
• Interior lamp loaded signal <vehicles with keyless
entry system>
If this function does not work normally, these input
signal circuit(s) or the ETACS-ECU may be
defective.
POSSIBLE CAUSES
• Malfunction of the door switches
• Malfunction of the room lamp switches
• Malfunction of the driver's door lock actuator
• Malfunction of the ETACS-ECU
• Malfunction of the key reminder switch
• Damaged harness wires and connectors
DIAGNOSTIC PROCEDURE
Step 1. Customize function by using the SWS
monitor
Use the SWS monitor customisation function to
confirm that "RM LMP TN OFF" is set to other than
"0 second" (one of the settings below).
• 30 seconds
• 15 seconds
• 7.5 seconds
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Use the SWS monitor customisation
function to confirm that "RM LMP TN OFF"
is set to other than "0 second" (Refer to
).
KEY CYLINDER
ILLUMINATION
LAMP
· ROOM LAMP
· DOOR LAMP
· LUGGAGE
COMPARTMENT
LAMP
· REAR PERSONAL
LAMP
KEEP RELAY
LOAD
DETERMINATION
CIRCUIT
J/B SIDE
ETACS-ECU
FUSIBLE
LINK
26
Interior Lamp Circuit <with keyless entry system>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-376
Step 2. ECU check by using the SWS monitor
Check that the power supply and earth lines to the
ETACS-ECU and the SWS communication lines are
normal.
• Ignition switch: OFF
ECUS TO BE CHECKED
• ETACS ECU
OK: "OK" is displayed on the "ETACS ECU"
menu.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to Inspection Procedure A-3
"Communication with ETACS-ECU is not
possible
Step 3. Check the illumination of the interior
lamps.
Check that the interior lamps illuminate and
extinguish.
NOTE: Check that the interior lamps illuminate or
extinguish when the interior lamp switches are
operated. For the room lamp and the rear personal
lamps, check they illuminate when the lamp switches
are turned to the ON or DOOR position.
Q: Which of the interior lamp does no illuminate or
extinguish?
All of the interior lamps illuminate and extinguish
normally. :
The procedure is complete.
No lamps illuminate at all. :
Replace the
ETACS-ECU.
When the interior lamp switches are turned to the
ON position, no lamps illuminate at all.
Alternatively, when the interior lamp switches are
turned to the OFF position, all the interior lamps
illuminate. :
Refer to inspection procedure Q-22
"The interior lamp "all on" or "all off" switch
signal is not sent to the ETACS-ECU
."
If the interior lamp switches are turned to the ON
position, none of the room lamp and the rear
personal lamps illuminate at all. :
Go to Step 4.
The room lamp and the rear personal lamps do not
illuminate or extinguish normally when the
switches are at the DOOR position. :
Go to Step 6.
Only the room lamp does not illuminate or
extinguish normally. :
Refer to inspection
procedure Q-22 "The interior lamp "all on"
or "all off" switch signal is not sent to the
ETACS-ECU
."
Only right or left rear personal lamp does not
illuminate or extinguish normally. :
Refer to
inspection procedure Q-22 "The interior
lamp "all on" or "all off" switch signal is not
sent to the ETACS-ECU
."
Only the luggage compartment lamp does not
illuminate or extinguish normally. :
Refer to
inspection procedure Q-22 "The interior
lamp "all on" or "all off" switch signal is not
sent to the ETACS-ECU
."
Only the door lamps do not illuminate or
extinguish normally. :
Refer to inspection
procedure Q-22 "The interior lamp "all on"
or "all off" switch signal is not sent to the
ETACS-ECU
."
Only the key cylinder illumination lamp does not
illuminate or extinguish normally. :
Refer to
inspection procedure Q-22 "The interior
lamp "all on" or "all off" switch signal is not
sent to the ETACS-ECU
."
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-377
Step 4. Connector check: C-219 ETACS-ECU
connector and E-02 room lamp connector
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the defective connector.
AC310626
Connector: C-219
Junction block (Rear view)
<LHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310651
AD
Connector: E-02 <LHD>
Harness side
AC310655
AE
Connector: E-02 <RHD>
Harness side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст