Mitsubishi Grandis. Manual — part 1027
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-160
STEP 5. Connector check: SRS-ECU connector
C-119, ignition switch connector C-307, joint
connector C-01 <LHD: diagnosis code B1477>,
joint connector C-33 <RHD: diagnosis code
B1477>, junction block connector C-202 and
C-205.
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-161
Q: Is the check result normal?
YES :
Check the harness wire for open circuit
between SRS-ECU connector C-119
(terminal No.24 <B1476> or terminal No.23
<B1477>) and the ignition switch connector
C-307 (terminal No.2), and repair if
necessary. Then go to Step 10.
NO :
Repair or replace it. Then go to Step 10.
AC311438 AD
C-119 (Y)
Connector: C-119
Harness side
(front view)
AC313147AD
Connector: C-307 <LHD>
C-307
2
5
4
1
6
3
AC313148
AD
Connector: C-307<RHD>
C-307
2
5
4
1
6
3
AC310613
AE
Connector: C-01 <LHD>
AC310631BD
Connector: C-33 <RHD>
AC310624
Connectors: C-202, C-205 <LHD>
AF
Junction block (Front view)
C-205
C-202
C-205
Harness side
C-202
Harness side
AC310619
Connectors: C-202, C-205 <RHD>
AF
Junction block (Front view)
C-205
C-202
C-205
Harness side
C-202
Harness side
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-162
STEP 6. Check a burned-out fuse.
(1) Replace the fuse.
(2) Turn the ignition switch to the "ON" position, wait
for at least one minute and then turn the ignition
switch to the "LOCK" (OFF) position.
(3) Check the fuse.
Q: Is the fuse in good condition?
YES :
Go to Step 10.
NO :
It is possible that the circuit using fuse No.2
<B1476> or No.3 <B1477> is shorted, go to
Step 7.
STEP 7. Check the SRS-ECU power supply
circuit for short circuit to earth. Resistance
measurement at the junction block connector
C-205.
(1) Disconnect junction block connector C-205, and
measure at the wiring harness side.
CAUTION
Do not insert a test probe into the terminal from
its front side directly as the connector contact
pressure may be weakened.
(2) Measure the resistance between terminal 24
<B1476> or 7 <B1477> and body earth.
OK: Open circuit
Q: Is the check result normal?
YES :
Check the other circuit, which flows through
fuse No.2 <B1476> or fuse No.3
<B1477>.Then go to Step 10.
NO :
Go to Step 8.
STEP 8. Check the power supply circuit for short
circuit to earth. Resistance measurement at the
SRS-ECU connector C-119.
(1) Disconnect SRS-ECU connector C-119, and
AC310623
Connector: C-205 <LHD>
AM
Harness side
Junction block (Front view)
AC310618
Connectors: C-205 <RHD>
AL
Harness side
Junction block (Front view)
AC308200
1 2 3 4 5 6 7 8 9 10 1112 1314
1516 1718 19 20 212223 242526 2728
C-205 Harness side
connector (rear view)
AC
AC311438 AD
C-119 (Y)
Connector: C-119
Harness side
(front view)
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-163
measure at the wiring harness side.
CAUTION
Do not insert a test probe into the terminal from
its front side directly as the connector contact
pressure may be weakened.
(2) Measure the resistance between terminal 24
<B1476> or 23 <B1477> and body earth.
OK: Open circuit
Q: Does continuity exist?
YES :
Erase the diagnosis code memory, and
check the diagnosis code. If diagnosis code
B1476 or B1477 sets, replace the
SRS-ECU. (Refer to
). Then go to
Step 10.
NO :
Go to Step 9.
AC308195
42
31
38
27
21
41
28
39
22
30
25
47
36
33
44
34
45
37
48
26
29
23
40
32
43
35
46
24
B
A
C-119 Harness side
connector (rear view)
AD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст