Mitsubishi Outlander (2013+). Manual — part 528
KEYLESS ENTRY SYSTEM <Vehicles without keyless operation system>
BODY
42A-132
PROBABLE CAUSES
• Malfunction of the keyless entry transmitter
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
1. Check the operation of the keyless entry system.
2. Check the customise function.
3. Retest the system.
Inspection Procedure 4: Multimode keyless entry system function does not work at all <Vehicles with
electric retractable remote controlled door mirrors>.
CAUTION
Before replacing the ECU, ensure that the power
supply circuit, the earth circuit and the communi-
cation circuit are normal.
COMMENTS ON TROUBLE SYMPTOM
If the electric-folding door mirrors work normally,
ETACS-ECU may be faulty. Also, the door mirror
operation setting is configured for other than the fold-
ing/unfolding interlocked with the keyless entry oper-
ation, using the customisation function.
PROBABLE CAUSES
• Malfunction of keyless entry transmitter
• Malfunction of ETACS-ECU
• Damaged wiring harness and connectors
DIAGNOSIS PROCEDURE
STEP 1. Confirm the transmitter.
Check that the keyless entry system works normally.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to trouble symptom chart
.
STEP 2. Check the operation of the
electric-folding door mirror.
Check that the electric folding door mirrors work nor-
mally.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to GROUP 51
− Troubleshooting .
STEP 3. M.U.T.-III diagnosis code
Check if any diagnosis code is set to the keyless
entry system.
Q: Is the diagnosis code set?
YES :
Refer to diagnosis code chart
.
NO :
Go to Step 4.
STEP 4. Check the customisation function.
Use the customisation function to check that the
"Multi mode" has been set to one of the followings,
not "Disabled."
• D/M: O&C.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Use the customisation function to set the
"Multi mode" to one of the above, not
"Disabled" (Refer to
STEP 5. Check of the troubles
Check that the multimode keyless entry system
works normally.
Q: Is the check result normal?
YES :
Intermittent malfunction (Refer to GROUP
00
− How to Use
Troubleshooting/Inspection Service Points
−
How to Cope with Intermittent Malfunction ).
NO :
Replace ETACS-ECU and register the ID
codes (Refer to
Inspection Procedure 5: Power door locks with selective unlocking does not work.
CAUTION
Before replacing the ECU, ensure that the power
supply circuit, the earth circuit and the communi-
cation circuit are normal.
COMMENT ON TROUBLE SYMPTOM
If the keyless entry function works normally and only
the power door locks with selective unlocking does
not work normally, ETACS-ECU may be defective. In
addition, it is possible that the function has been dis-
abled by using the customisation function.
KEYLESS ENTRY SYSTEM <Vehicles without keyless operation system>
BODY
42A-133
PROBABLE CAUSES
• Malfunction of ETACS-ECU
• Damaged wiring harness and connectors
DIAGNOSIS PROCEDURE
STEP 1. Check the customisation
Q: Are the power door locks with selective unlocking
enabled by the customization function?
YES :
Go to Step 2.
NO :
Set the power door locks with selective
unlocking to "Enabled" by using the
customisation function. Refer to
STEP 2. Keyless entry system operation check
Press the unlock switch of the transmitter and check
that only the driver's door is unlocked. Then, press
the unlock switch once again within 2 seconds after
that to check that the front passenger's door, the rear
doors and the tailgate are unlocked.
Q: Does the keyless entry system work normally?
YES :
Go to Step 3.
NO (Only the driver's door is not unlocked.) :
Replace the ETACS-ECU and register the
ID codes (Refer to
NO (The driver's door, front passenger's door, rear
doors and tailgate are not unlocked.) :
Refer to
Inspection Procedure 1: "Keyless entry
system does not work
."
STEP 3. Check of the troubles
Check that the power door locks with selective
unlocking works normally.
Q: Is the check result normal?
YES :
Intermittent malfunction (Refer to GROUP
00
− How to Use
Troubleshooting/Inspection Service Points
−
How to Cope with Intermittent Malfunction ).
NO :
Replace ETACS-ECU and register the ID
codes (Refer to
CHECK AT ECU TERMINAL
M1428006600017
Receiver antenna terminal check (Refer to GROUP
54A
− Check at ECU terminal ).
ON-VEHICLE SERVICE
KEYLESS ENTRY SYSTEM INSPECTION
M1428001400449
Check the system as described below. If the system
does not work, carry out troubleshooting. Refer to
• Operate the transmitter to check that the doors
can be locked and unlocked.
• Operate the transmitter to check when the door
locking or unlocking operation is performed that
the hazard warning lamp [lock: flash once,
unlock: flash twice (default setting)] and room
lamp [lock: flash once, unlock: illuminates for 15
seconds (default setting)] answer back operates.
Refer to
.
NOTE:
.
•
The customisation function allows you to
change the answerback setting as follows.
Prior to that check, confirm which setting is
activated.
•
The hazard warning lamp flash once when
locked and twice when unlocked (default
setting).
•
The hazard warning lamp flash once when
locked and do not flash when unlocked.
•
The hazard warning lamp do not flash
when locked and flash twice when
unlocked.
•
The hazard warning lamp do not flash
when both locked and unlocked.
•
The hazard warning lamp flash twice
when locked and once when unlocked.
•
The hazard warning lamp flash twice
when locked and do not flash when
unlocked.
•
The hazard warning lamp do not flash
when locked and flash once when
unlocked.
KEYLESS ENTRY SYSTEM TIMER LOCK
FUNCTION INSPECTION
M1428004000547
Attempt to unlock the doors by using the transmitter.
If the doors are not locked within 30 seconds, carry
out troubleshooting. Note that the doors will not be
locked if the ignition key is inserted within the 30-sec-
ond period, one of the doors is opened, or the key-
less entry function is triggered. Refer to
NOTE: The customise function allows you to change
the keyless entry system timer lock period from 30
seconds (initial setting) to 60, 120 or 180 seconds.
Prior to the check, confirm which setting is activated.
Refer to
KEYLESS ENTRY SYSTEM <Vehicles without keyless operation system>
BODY
42A-134
MULTIMODE KEYLESS ENTRY
FUNCTION CHECK <Vehicles with
electric retractable remote controlled
door mirrors>
M1428004100254
Operate the transmitter to check that the elec-
tric-folding door mirrors work. If they do not work,
carry out diagnosis. Refer to
.
NOTE: The settings of the electric-folding door mir-
rors can be changed using the customisation func-
tion. Confirm which settings are activated before
performing diagnosis. Refer to
POWER DOOR LOCKS WITH SELECTIVE
UNLOCKING INSPECTION
M1428006400068
Press the unlock switch on the transmitter once to
unlock only the driver's door. Press the unlock switch
of the transmitter once again within 2 seconds after
the driver's door is unlocked, and check that the front
passenger's door, the rear doors and tailgate are
unlocked. If they are not unlocked, carry out trouble-
shooting. Refer to
.
NOTE: Press the unlock switch on the transmitter
once to unlock only the driver's door. When the
unlock switch of the transmitter is pressed once
again more than 2 seconds after the driver's door is
unlocked, only the driver's door is unlocked.
NOTE: The setting of the power door locks with
selective unlocking can be changed using the cus-
tomisation function. Confirm which setting is acti-
vated before performing these checks. Refer to
HOW TO REGISTER ENCRYPTED CODE
M1428001001239
For the details of key registration procedure, refer to
the ID registration procedure manual.
CUSTOMISATION FUNCTION
M1428005500255
By operating the M.U.T.-III ETACS system, the fol-
lowing functions can be customised. The pro-
grammed information is held even when the battery
is disconnected.
Adjustment
item (M.U.T.-III
display)
Adjustment item
Adjusting content
(M.U.T.-III display)
Adjusting content
Hazard answer
back
Adjustment of the
number of keyless
hazard warning
lamp answer back
flashes
Lock:1, Unlock:2
LOCK: Flashes once, UNLOCK: Flashes
twice (initial condition)
Lock:1, Unlock:0
LOCK: Flashes once, UNLOCK: No flash
Lock:0, Unlock:2
LOCK: No flash, UNLOCK: Flash twice
Lock:2, Unlock:1
LOCK: Flash twice, UNLOCK: Flash once
Lock:2, Unlock:0
LOCK: Flash twice, UNLOCK: No flash
Lock:0, Unlock:1
LOCK: No flash, UNLOCK: Flash once
Lock:0, Unlock:0
No function
Auto fold mirror
Electric folding door
mirror automatic
unfolding function
<vehicles with
electric retractable
remote controlled
door mirrors>
Not Auto
No synchronised operation
Open Vehicle SPD
Vehicle speed-dependent operation
Open/Close by IG
Ignition switch linked operation
OPN/CLS Keyles
Keyless entry linked operation (initial
condition)
Door unlock
mode
Adjustment of
power door locks
with selective
unlocking
All Doors Unlock
Without function: The first operation of
keyless entry system or unlock operation
by KOS unlocks all doors (initial condition).
Dr Door Unlock
With function: The first operation of
keyless entry system or unlock operation
by KOS unlocks the driver's door only, and
the second unlock operation within 2
seconds after that unlocks all doors.
KEYLESS ENTRY SYSTEM <Vehicles without keyless operation system>
BODY
42A-135
TRANSMITTER
DISASSEMBLY AND REASSEMBLY
M1428002800525
Post-installation operation
• Transmitter operation check
AC310838
AC303199
AC304118
1
2
AI
5
3
4
6
Disassembly steps
1.
Screw
2.
Upper cover
3.
Transponder
4.
Transmitter assembly
<<
A
>>
>>
A
5.
Battery
6.
Master key
Timer lock timer Timer lock period
adjustment
30 sec
30 seconds (initial condition)
60 sec
60 seconds
120 sec
120 seconds
180 sec
180 seconds
Multi mode
Multi-mode keyless
entry function
customisation
<Vehicles with
electric retractable
remote controlled
door mirrors>
Disable
No function
D/M: O&C
Door mirror fold/unfold operation only
(initial condition)
Adjustment
item (M.U.T.-III
display)
Adjustment item
Adjusting content
(M.U.T.-III display)
Adjusting content
Disassembly steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст