Mitsubishi Outlander (2013+). Manual — part 748

AMBIENT TEMPERATURE SENSOR

HEATER, AIR CONDITIONER AND VENTILATION

55-48

INSTALLATION SERVICE POINT

>>A<< OUTSIDE/INSIDE AIR SELECTION
DAMPER CONTROL MOTOR INSTALLA-
TION

Install the outside/inside air selection damper control
motor while pressing the outside/inside air selection
damper from the hole of the blower motor.

>>B<< CLEAN AIR FILTER
INSTALLATION

7803A004

>PP.PET<

helsatech PF087

Made in

XX.XX.XX

XX:XX

AIR FLOW

AC508409

AC

Front view

Install with the arrow
facing down.

Install the clean air filter in the direction shown.

INSPECTION

M1552014305182

BLOWER MOTOR CHECK

AC611918

AK

Check that the motor turns when applying battery
power between the connector terminals. Also check
to see that there is no abnormal sound emitted from
the motor at this time.

AMBIENT TEMPERATURE SENSOR

REMOVAL AND INSTALLATION

M1554003400915

Pre-removal and Post-installation Operation
• Air cleaner intake duct (Refer to GROUP 15, Air Cleaner )

• Headlamp support upper panel cover (Refer to GROUP

51, Radiator Grille )

ACB04999

1

AB

Removal

1.

Ambient temperature sensor

INTERIOR TEMPERATURE SENSOR

HEATER, AIR CONDITIONER AND VENTILATION

55-49

INSPECTION

M1552014305193

AMBIENT TEMPERATURE SENSOR
CHECK

AC508067AC

10

7

6
5

9
8

4
3
2
1
0

10

20

30

40

-10

0

RESISTANCE

TEMPERATURE (˚C)

(k )

Check to see that the resistance shown in the graph
is almost satisfied when measuring the resistance
between the terminals under two or more different
temperature conditions.

INTERIOR TEMPERATURE SENSOR

REMOVAL AND INSTALLATION

M1554026400488

WARNING

For removal and installation of the Knee air bag module, always observe the service proce-
dures described in GROUP 52B, Knee Air Bag Module .

Pre-removal and Post-installation Operation
• Knee air bag module (Refer to GROUP 52B − Knee Air

Bag Module ).

ACB05823

2

1

AB

A

A

Claw

1

AC704919

Instrument panel

Section A-A

Removal steps

1.

Aspirator hose

2.

Interior temperature sensor

COMPRESSOR ASSEMBLY

HEATER, AIR CONDITIONER AND VENTILATION

55-50

INSPECTION

M1552014305201

INTERIOR TEMPERATURE SENSOR
CHECK

AC103488

20

15

10

5

0

-10 0

20

40

60

80

AD

RESISTANCE

TEMPERATURE (˚C)

(k )

Check to see that the resistance shown in the graph
is almost satisfied when measuring the resistance
between the terminals under two or more different
temperature conditions.

COMPRESSOR ASSEMBLY

REMOVAL AND INSTALLATION

M1552004403609

CAUTION

•

Pre-removal operation
• Discharging refrigerant (Refer to

P.55-34

)

• Engine room under cover front A and B, Engine room side

cover removal (Refer to GROUP 51, Under Cover ).

• Drive belt removal (Refer to GROUP 11A − Crankshaft

Pulley )

Post-installation Operation
• Drive belt installation (Refer to GROUP 11A − Crankshaft

Pulley )

• Drive belt tension check and adjustment (Refer to

GROUP 11A

− Drive Belt Tension Check ).

• Charging refrigerant (Refer to

P.55-34

)

• Engine room under cover front A and B, Engine room side

cover installation (Refer to GROUP 51, Under Cover ).

AC900337

1, 2

3

5

3

1

2

4

AG

3

N

N

10 ± 2 N·m

10 ± 2 N·m

23 ± 6 N·m

23 ± 6 N·m

A/C compressor oil:
SUN PAG 56 or S10X

-Pipe coupling

23 ± 6 N·m

6

23 ± 6 N·m

When removing the compressor, be careful not to subject the pulley and the clutch to impact.

Removal steps

<<

A

>>

1.

A/C compressor discharge hose

<<

A

>>

2.

A/C compressor suction hose

3.

O-ring

<<

B

>>

>>

A

<<

4.

A/C compressor and clutch
assembly

5.

A/C compressor bracket A

5.

A/C compressor bracket B

COMPRESSOR ASSEMBLY

HEATER, AIR CONDITIONER AND VENTILATION

55-51

NOTE: The service points which are not described
are the same as before.

REMOVAL SERVICE POINTS

<<A>> DISCHARGE FLEXIBLE
HOSE/SUCTION FLEXIBLE HOSE DIS-
CONNECTION

CAUTION

Use the plug which is not breathable because
A/C compressor oil or receiver have high hygro-
scopicity.
Plug the hose nipple removed to prevent the entry of
dust and dirt.

<<B>> A/C COMPRESSOR AND CLUTCH
ASSEMBLY REMOVAL

Be careful not to spill the A/C compressor oil and
remove the A/C compressor.

INSTALLATION SERVICE POINT

>>A<< A/C COMPRESSOR AND CLUTCH
ASSEMBLY INSTALLATION

If a new compressor is installed, first adjust the
amount of oil according to the procedures described
below, and then install the compressor.
1. Measure the amount X mL of oil within the

removed compressor.

2. Drain (from the new compressor) the amount of

oil calculated according to the following formula,
and then install the new compressor.

New compressor oil amount = 70mL

70 mL

− X mL = Y mL

NOTE: Y mL indicates the amount of oil in the refrig-
erant line, the condenser, the evaporator, etc.

AC711141AD

1

2

3

A/C compressor and
clutch assembly

3. Tighten A/C compressor assembly mounting bolts

to the specified torque in the order of number
shown in the figure.

Tightening torque: 23

± 6 N⋅m

INSPECTION

M1552004501473

CHECK THE MAGNETIC CLUTCH FOR
A/C COMPRESSOR

AC809068

Connect the connector battery to positive battery ter-
minal in the A/C compressor, and then earth the bat-
tery (

−) terminal to the A/C compressor itself. At this

time, check that the magnetic clutch operating sound
can be heard.