Mitsubishi Outlander (2013+). Manual — part 685
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-225
YES :
Replace the radio and CD player.
NO :
A poor connection, open circuit or other
intermittent malfunction in the CAN bus line
between the radio and CD player and the
KOS-ECU. (Refer to GROUP 00
− How to
Use Troubleshooting/Inspection Service
Points - How to Cope with Intermittent
Malfunction .)
Code No.U0230 Power Gate CAN Timeout
CAUTION
• If diagnosis code No. U0230 is set, be sure to
diagnose the CAN bus line.
• When replacing the radio and CD player,
always check that the communication circuit
is normal.
DIAGNOSTIC FUNCTION
If the signal from electric tailgate control unit cannot
be received, the radio and CD player sets the diag-
nosis code No. U0230.
JUDGEMENT CRITERIA
With the statuses that the ignition switch is at ON
position, system voltage is 10
− 16 V (data from
ETACS-ECU), and there is no malfunction to the
power supply fuse (IOD fuse), or odometer value is
80.5 km or more, if the communication with electric
tailgate control unit cannot be established for 2,500
ms or more, the radio and CD player determines that
a problem has occurred.
PROBABLE CAUSES
• Malfunction of CAN bus line
• Malfunction of electric tailgate control unit
• Malfunction of radio and CD player
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the CAN bus line (Refer to GROUP
54C
− Troubleshooting ).
STEP 2. M.U.T.-III other system diagnosis code
Check again if the diagnosis code is set to the elec-
tric tailgate control unit.
Q: Is the diagnosis code set?
YES :
Troubleshoot the electric tailgate control unit
(Refer to GROUP 42A
− Tailgate <vehicles
with electric tailgate>
− Diagnosis Code
Chart ), and then go to Step 3.
NO :
Go to Step 3.
STEP 3. Check the M.U.T.-III Diagnosis code for
other systems
Check if the diagnosis code No. U0230 is set to
ETACS-ECU.
Q: Is the diagnosis code set?
YES :
Go to Step 4.
NO :
Go to Step 5.
STEP 4. Diagnosis code recheck
Check again if the diagnosis code is set to the radio
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF)
position to the "ON" position.
(3) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Replace the electric tailgate control unit.
NO :
A poor connection, open circuit or other
intermittent malfunction in the CAN bus line
between the radio and CD player and the
electric tailgate control unit. (Refer to
GROUP 00
− How to Use
Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunction .)
STEP 5. Check whether the diagnosis code is
reset.
Check again if the diagnosis code is set to the radio
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF)
position to the "ON" position.
(3) Check if diagnosis code is set.
Q: Is the diagnosis code set?
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-226
YES :
Replace the radio and CD player.
NO :
A poor connection, open circuit or other
intermittent malfunction in the CAN bus line
between the radio and CD player and the
electric tailgate control unit. (Refer to
GROUP 00
− How to Use
Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunction .)
Code No.U1000 OSS CAN timeout
CAUTION
• If diagnosis code No. U1000 is set, be sure to
diagnose the CAN bus line.
• When replacing the radio and CD player,
always check that the communication circuit
is normal.
DIAGNOSTIC FUNCTION
If the signal from OSS-ECU cannot be received, the
radio and CD player sets the diagnosis code No.
U0230.
JUDGEMENT CRITERIA
With the statuses that the ignition switch is at ON
position, system voltage is 10
− 16 V (data from
ETACS-ECU), and there is no malfunction to the
power supply fuse (IOD fuse), or odometer value is
80.5 km or more, if the communication with
OSS-ECU cannot be established for 2,500 ms or
more, the radio and CD player determines that a
problem has occurred.
PROBABLE CAUSES
• Malfunction of CAN bus line
• Malfunction of OSS-ECU
• Malfunction of radio and CD player
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the CAN bus line (Refer to GROUP
54C
− Troubleshooting ).
STEP 2. M.U.T.-III other system diagnosis code
Check again if the diagnosis code is set to the
OSS-ECU.
Q: Is the diagnosis code set?
YES :
Troubleshoot the OSS-ECU (Refer to
GROUP 42B
− Diagnosis Code Chart ), and
then go to Step 3.
NO :
Go to Step 3.
STEP 3. Check the M.U.T.-III Diagnosis code for
other systems
Check if the diagnosis code No. U1000 is set to
ETACS-ECU.
Q: Is the diagnosis code set?
YES :
Go to Step 4.
NO :
Go to Step 5.
STEP 4. Diagnosis code recheck
Check again if the diagnosis code is set to the radio
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF)
position to the "ON" position.
(3) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Replace the OSS-ECU.
NO :
A poor connection, open circuit or other
intermittent malfunction in the CAN bus line
between the radio and CD player and the
OSS-ECU. (Refer to GROUP 00
− How to
Use Troubleshooting/Inspection Service
Points - How to Cope with Intermittent
Malfunction .)
STEP 5. Check whether the diagnosis code is
reset.
Check again if the diagnosis code is set to the radio
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF)
position to the "ON" position.
(3) Check if diagnosis code is set.
Q: Is the diagnosis code set?
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-227
YES :
Replace the radio and CD player.
NO :
A poor connection, open circuit or other
intermittent malfunction in the CAN bus line
between the radio and CD player and the
OSS-ECU. (Refer to GROUP 00
− How to
Use Troubleshooting/Inspection Service
Points - How to Cope with Intermittent
Malfunction .)
Code No.U1190 No receive fault detect signal
CAUTION
• Before replacing the ECU, ensure that the
power supply circuit, the earth circuit and the
communication circuit are normal.
• When the ETACS-ECU of vehicles without
KOS is replaced, the encrypted code of the
ignition key needs to be registered to the
ETACS-ECU. (If the encrypted code is not reg-
istered, the engine cannot be started. Regis-
ter the encrypted code as described in
Immobilizer System
− How to Register Key ID
JUDGEMENT CRITERIA
ETACS-ECU sends the diagnosis code (U code)
detection permission or prohibition signal to each
ECU connected to the CAN bus line. If the radio and
CD player cannot receive the diagnosis code (U
code) detection permission or prohibition signal for 5
seconds after turning the electric motor switch to ON
position, diagnosis code U1190 will be set.
PROBABLE CAUSES
• Malfunction of the ETACS-ECU
• Malfunction of CAN bus line
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 2
NO :
Repair the CAN bus line (Refer to GROUP
54C
− Troubleshooting ). On completion, go
to Step 3.
STEP 2. Check whether the diagnosis code is
reset.
Check again if the diagnosis code is set to the radio
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF)
position to the "ON" position.
(3) On completion, check that the diagnosis code is
reset.
Q: Is the diagnosis code set?
YES :
Replace the ETACS-ECU. Then go to Step
3.
NO :
The procedure is complete.
STEP 3. Check whether the diagnosis code is
reset.
Recheck if the diagnosis code is set to the radio and
CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF)
position to the "ON" position.
(3) On completion, check that the diagnosis code is
reset.
Q: Is the diagnosis code set?
YES :
Return to Step 1.
NO :
The procedure is complete.
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-228
Code No. U1195 Coding not completed
CAUTION
• If the diagnosis code No. U0164 is set, be sure
to diagnose the CAN bus line.
• When replacing the radio and CD player,
always check that the communication circuit
is normal.
• When the diagnosis code No.U1195 is set in
radio and CD player, the diagnosis code may
also be set in ETACS-ECU. When the diagno-
sis code is set in ETACS-ECU, carry out the
diagnosis of the diagnosis code for
ETACS-ECU first.
JUDGEMENT CRITERIA
This diagnosis code is set when the variant coding
for ETACS-ECU has not been implemented.
PROBABLE CAUSES
• Variant coding for ETACS-ECU has not been
implemented.
• Malfunction of radio and CD player
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnosis
Use M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the CAN bus lines (Refer to GROUP
54C
− CAN Bus Diagnostics Table ). On
completion, go to Step 4.
STEP 2. M.U.T.-III other system diagnosis code
Use M.U.T.-III to check that the diagnosis code
No.B222C is set in the ETACS-ECU.
Q: Is the diagnosis code set?
YES :
Troubleshoot the relevant diagnosis code,
and then go to Step 4.
NO :
Go to Step 3.
STEP 3. Check whether the diagnosis code is
reset.
Check again if the diagnosis code is set to the radio
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF)
position to the "ON" position.
(3) Check if the diagnosis code is set.
Q: Is the diagnosis code No.U1195 set?
YES :
Replace the radio and CD player, and then
go to Step 4.
NO :
Intermittent malfunction (Refer to GROUP
00
− How to Use Troubleshooting/How to
Cope with Intermittent Malfunctions ).
STEP 4. Check whether the diagnosis code is
reset.
Check again if the diagnosis code is set to the radio
and CD player.
(1) Erase the diagnosis code.
(2) Turn the ignition switch from the "LOCK" (OFF)
position to the "ON" position.
(3) Check if the diagnosis code is set.
Q: Is the diagnosis code No.U1195 set?
YES :
Return to Step 1.
NO :
This diagnosis is complete.
TROUBLE SYMPTOM CHART
M1544004902769
Trouble symptom
Inspection
Procedure No.
Reference
page
Power of the radio and tape player does not turn ON when the ignition switch
is in the "ACC" position or "ON" position.
1
No sound is heard.
2
The radio broadcasting can not be received.
3
Audio illumination does not work normally.
4
NOTE:
.
•
For the troubleshooting of the hands free-ECU,
refer to
.<Vehicles with display audio>
•
For the troubleshooting of the steering wheel
audio remote control switch, refer to
.<Vehicles with display audio>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст