Mitsubishi Outlander (2013+). Manual — part 404

DRIVESHAFT ASSEMBLY

REAR AXLE <4WD>

27B-20

>>B<< ETJ BOOT BAND (SMALL)/ETJ
BOOT BAND (LARGE) TIGHTENING

AC102657AB

A

Adjust the distance between the boot bands to the
standard value to adjust the air volume inside the
ETJ boot to the specified value, then be sure to
tighten the ETJ boot band (large) and ETJ boot band
(small).

Standard value (A): 75

± 3 mm

DIFFERENTIAL CARRIER ASSEMBLY

REAR AXLE <4WD>

27B-21

DIFFERENTIAL CARRIER ASSEMBLY

REMOVAL AND INSTALLATION

M1271005300392

CAUTION

•

Pre-removal operation
• Spare tyre and spare tyre carrier removal (Refer to

GROUP 31, Spare Tyre Carrier ).

• Centre exhaust pipe and main muffler removal (Refer to

GROUP 15, Exhaust Pipe and Muffler ).

• Drain differential gear oil.
• Drive shaft removal (Refer to

P.27B-14

).

Post-installation operation
• Drive shaft installation (Refer to

P.27B-14

).

• Fill the differential gear oil.

• Centre exhaust pipe and main muffler installation (Refer

to GROUP 15, Exhaust Pipe and Muffler ).

• Spare tyre and spare tyre carrier installation (Refer to

GROUP 31, Spare Tyre Carrier ).

ACB05750AB

54 ± 5 N·m

95 ± 14 N·m

71 ± 10 N·m

1

N

32 ± 2 N·m

71 ± 10 N·m

95 ± 14 N·m

110 ± 11 N·m

9.8 ± 1.9 N·m

2

3

N

32 ± 2 N·m

4

7

5

6

*

*

*

7.0 ± 3.0 N·m

9

10

11

13

8

9

10

11

12

13

14

The parts indicated by * are the bolts with friction coefficient stabilizer. In removal, ensure there is
no damage, clean dust and soiling from the bearing and thread surfaces, and tighten them to the
specified torque.

Removal steps

<<

A

>>

1.

Propeller shaft connection

2.

Filler plug

3.

Gasket

4.

Drain plug

5.

Gasket

6.

Cover

7.

Electronic control coupling
harness connection, breather
hose connection

Removal steps (Continued)

DIFFERENTIAL CARRIER ASSEMBLY

REAR AXLE <4WD>

27B-22

REMOVAL SERVICE POINT

<<A>> PROPELLER SHAFT DISCONNEC-
TION

ACB05381

Mating marks

AB

1. Put mating marks on the flange yoke and the

electronic control coupling.

2. Hold the disconnected propeller shaft with a wire

so that it will not be bent sharply.

INSTALLATION SERVICE POINT

>>A<< DIFFERENTIAL CARRIER ASSEM-
BLY INSTALLATION

ACC00420

Electronic control coupling

A

AB

1. Check that the length of the electronic control

coupling stud bolt (A) is within the standard value
range.

Standard value: 21.6

− 24.4 mm

2. If the length exceeds the standard value, replace

the stud bolt.

Tightening torque: 15

± 3 N⋅m

NOTE: When replacing the stud bolts, always
clean the stud bolt threaded holes.

8.

Differential to rear suspension
crossmember connecting bolt

9.

Weight

10. Lower stopper
11. Upper stopper

>>

A

<<

12. Differential carrier assembly
13. Differential mount bracket (LH/RH)
14. Differential bracket

Removal steps (Continued)

DIFFERENTIAL CARRIER ASSEMBLY

REAR AXLE <4WD>

27B-23

DISASSEMBLY

M1271005400225

ACB05751

14

12

11

29

5

20

33

1

7

8

N

N

4

N

N

N

19

18

17

10

AB

3

2

N

6

9

10

11

13

12

15

16 17

18

19

20

21

22

23

24

25

26

27

28

30

31

32

13

Disassembly steps

1.

Filler plug

2.

Gasket

3.

Drain plug

4.

Gasket

5.

Electronic control coupling

6.

Wave washer

7.

Differential cover assembly

8.

Vent plug

9.

Oil seal

<<

A

>>

•

Pre-disassembly check

<<

B

>>

10. Differential case assembly

<<

B

>>

11. Differential side bearing spacer

<<

B

>>

12. Differential side bearing outer race

<<

C

>>

13. Differential side bearing inner race

<<

D

>>

14. Drive gear

<<

E

>>

15. Lock pin
16. Pinion shaft
17. Pinion gear
18. Pinion washer
19. Side gear
20. Side gear spacer

21. Differential case

<<

F

>>

22. Differential nut
23. Drive pinion assembly
24. Drive pinion front shim (for drive

pinion rotation torque adjustment)

25. Drive pinion spacer

<<

G

>>

26. Drive pinion rear bearing inner

race

27. Drive pinion rear shim (for drive

pinion height adjustment)

28. Drive pinion
29. Oil seal
30. Drive pinion front bearing inner

race

<<

H

>>

31. Drive pinion front bearing outer

race

<<

I

>>

32. Drive pinion rear bearing outer

race

33. Differential carrier

Disassembly steps (Continued)