Mitsubishi Outlander (2013+). Manual — part 242

AC208446

Denotes connector No.
The same connector No. is used throughout the circuit diagrams to facilitate connector location search.
The first alphabetical symbol indicates the location site of the connector and a number that follows is the unique number.
Numbers are usually assigned to part in clockwise order on the diagram.

Example: A-19

Number specific to connector (serial number)

Connector location site symbol
A: Engine compartment
B: Engine and transmission
C: Instrument panel
D: Floor

E: Roof

F: Door
G: Tailgate

Denotes earth point.
Same earth number is used throughout circuit
diagrams to facilitate search of earth point.
Refer to GROUP 70 COMPONENT LOCATIONS
- EARTH MOUNTING LOCATIONS
for details of earth points.

Denotes the colour of the tube
(If not specified, it is black).
R: Red
Y: Yellow

The number of connector pins and the connector colour
(except milk white)* are shown for ease of retrieval.

Example: (2-B)

Connector colour
(milk white if no colour is indicated)

Number of connector pins

*: Typical connector colours
B: Black

BR: Brown

Y: Yellow

V: Violet

L: Blue

O: Orange

G: Green

GR: Grey

R: Red

None: Milk white

A-15 (2) Fog lamp (RH)
A-16 (2-GR) Horn (LO)
A-17 (2-B) Headlamp (RH)
A-18 (2-B) Windshield washer motor
A-19 (2-GR) Dual pressure switch

Indicates the device to which the
connector is connected.

The mark shows the
standard mounting position
of wiring harness.

BD

A-17

A-16

A-15

A-18

A-19

Y

Denotes a section covered by a
corrugated tube.

Front
wiring
harness
(RH)

Denotes harness name.

1

HOW TO READ WIRING DIAGRAMS

GENERAL <ELECTRICAL>

00E-3

HOW TO READ WIRING DIAGRAMS

GENERAL <ELECTRICAL>

00E-4

HOW TO READ CIRCUIT DIAGRAMS

M1001006500224

The circuit of each system from the fuse (or fusible link) to earth is shown. The power source is shown at the
top and the earth at the bottom to facilitate understanding of how the current flows. The circuit diagrams show
the state when switches are not operated.

ACA00087

FUSIBLE
LINK

1

FUSIBLE
LINK

2

ECU

MOTOR

MOTOR

ECU

SENSOR

SENSOR

SENSOR

RELAY
BOX

RELAY

RESISTOR

RESISTOR

SWITCH

IGNITION
SWITCH (IG1)

SOLENOID
VALVE 1

SOLENOID
VALVE 2

SOLENOID
VALVE
ASSEMBLY

DIODE

Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver

AB

Indicates power source.

Indicates connector number.
The same numbers are used in the
wiring harness diagram.
Connector and connector numbers
are shown at the lower part of the
page.
Connector numbers not enclosed
by frame indicate the device incor-
porated into wiring harness.

Indicates a wiring connector which is inside
the equipment and which is not shown in
the wiring harness configuration diagram.

Example C-15-2

Indicates a connector
which is inside the
equipment, numbered
in order starting from 1.

Indicates the connector number shown in
the wiring harness configuration diagram.

Indicates that these connectors
are the same intermediate
connectors.

Indicates that the diagram comes
from which belongs to the
block in the same circuit.

Indicates terminal number.

In case two or more connectors
are connected to the same
device, markings indicating the
same connector are connector
by a broken line.

Indicates harness junction where
wire diameter or colour changes.

Indicates intersections at
which the lead wires are
not connected.

Indicates intersections at
which the lead wires are
connected.

Indicates representative vehicle
body earth point. (Same number
as that of earth point in
EARTHING LOCATION).

Indicates that the terminal is a
spare one if the device (sensor
in this case) is not provided.

Indicates shield wire.

Indicates the connector symbol.
Connectors in the circuit diagram
are indicated in numerical order.

Indicates that the diagram contin-
ues at which belongs to the
block in the same circuit.

An "X" at the end of a connector
number indicates that the conn-
ector is connected to a central-
ized junction that is shown in the
section "Centralized Junction."

Indicates equipment which the
branched harness wire leads to.

Indicates harness junction point
numbers for another system.
The number corresponds to the
junction point number indicated
on another circuit diagram.

Each circuit diagram consists of
block(s).

Indicates that terminal is conne-
cted via a plate in the relay box.

HOW TO READ WIRING DIAGRAMS

GENERAL <ELECTRICAL>

00E-5

MARKINGS FOR CONNECTOR AND
EARTHING

M1001007900195

FUSIBLE
LINK

6

ECU

MOTOR
ASSEMBLY

SENSOR

RELAY

IGNITION
SWITCH (IG1)

SOLENOID
VALVE 1

Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver

INSPECTION
CONNECTOR

ACA00254AB

8

7

1, 5

2, 6

1, 4

1, 4

1, 5

3

9

3

1

2

HOW TO READ WIRING DIAGRAMS

GENERAL <ELECTRICAL>

00E-6

Item

No.

Connector/Earthing

Symbol

Contents

Connector
and terminal
marking

−

ACX01251AE

Male terminal

Male connector

ACX01252AD

Male terminal

The male and female terminals
are indicated as shown. The
connector with male terminal(s)
is called as male connector and
indicated by two connector
contour lines, while the
connector with female
terminal(s) is called as female
connector and indicated by
single connector contour line.

ACX01253 AI

Male connector

ACX01254 AD

Female terminal

Female connector

ACX01255AD

Female terminal

ACX01256 AH

Female connector

Connector
symbol
marking

1

ACX01257AD

Device

ACX01253

The symbol indicates the
connector is viewed as shown.
At a device connection, the
connector symbol on the device
side is shown. For an
intermediate connector, the
male connector symbol is
shown. For spare connectors
and check connectors, no
device is connected, and so the
harness-side connector symbol
is shown for these connectors.
However, a diagnosis connector
is exceptional.

2

ACX01258AD

Intermediate connector

3

ACX01816

Spare connector, check connector

AD

ACX01256