Mitsubishi Outlander (2013+). Manual — part 618
WARNING/CAUTION LABELS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-123
WARNING/CAUTION LABELS
M1524003002192
The labels indicating the precautions for handling
and maintenance of SRS air bags and seat belt with
pre-tensioner are attached to the locations shown in
the figure. If the label is damaged or is dirty, replace
with the new label.
ACC00073
AC506241
ACB03681
ACB05525
ACC00035
ACB05526
ACB05536
ACB05535
ACB05614
Driver's air bag module
Sunvisor
Seat belt pre-tensioner (right and left)
SRS-ECU
Passenger's (front) air bag module
Side-airbag module (right and left)
Curtain air bag module (right and left)
Knee air bag module
Passenger's air bag cut off switch
AB
WARNING/CAUTION LABELS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-124
FRONT IMPACT SENSORS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-125
FRONT IMPACT SENSORS
REMOVAL AND INSTALLATION
M1524001501938
CAUTION
• Disconnect the negative (−) battery terminal and wait for 60 seconds or more before starting work.
Insulate the disconnected (
−) terminal by wrapping the tape (Refer to the item 5 of Service Precau-
• Never attempt to disassemble or repair the front impact sensor. If faulty, replace it with new one(s).
• Handle the front impact sensor with sufficient caution, and do not drop the sensor or allow con-
tact with water, oil, or others. If denting, cracking, or deformation is discovered, replace it with
new one(s).
•
Pre-removal operation
• Turn the ignition switch to the LOCK (OFF) position.
• Disconnect the negative (−) battery terminal.
ACB05457AB
10 ± 2 N·m
10 ± 2 N·m
1
1
Removal steps
1.
Front impact sensor
Installation steps
>>
A
•
Pre-installation inspection
>>
B
1.
Front impact sensor
>>
C
•
Post-installation inspection
After deployment of an air bag, replace the front impact sensor with a new one.
FRONT IMPACT SENSORS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-126
REMOVAL SERVICE POINT
<<A>> FRONT IMPACT SENSOR CON-
NECTOR REMOVAL
ACB05523AC
Front impact
sensor
Headlamp support
panel upper
Slide the outer housing of the front impact sensor
connector in the arrow direction shown, and discon-
nect the connector.
INSTALLATION SERVICE POINTS
>>A<< PRE-INSTALLATION INSPECTION
Check the front impact sensor before installation
(Refer to
).
>>B<< FRONT IMPACT SENSOR
INSTALLATION
CAUTION
If the front impact sensor is not securely and cor-
rectly installed, the correct operation of air bag
and pre-tensioner is prevented.
>>C<< POST-INSTALLATION
INSPECTION
1. Connect the negative (
−) battery cable.
2. Turn the ignition switch to the "ON" position.
ACC00038AB
SRS warning lamp
3. Check that the SRS warning lamp is illuminated
for 6 to 8 seconds, and extinguished afterward.
4. If the lamp does not extinguish, perform the
troubleshooting (Refer to
INSPECTION
M1524001600608
CAUTION
If a dent, crack, deformation or rust is found,
replace the sensor with a new front impact sen-
sor.
1. Check the front impact sensor for dents, cracks,
deformation or rust.
2. Binding of wiring harness, damaged connector,
and deformation of terminal
3. Deformation and rust of headlamp support panel
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст