Mitsubishi Outlander (2013+). Manual — part 672
MB992006
HAZARD WARNING LAMP SWITCH
CHASSIS ELECTRICAL
54A-173
TROUBLESHOOTING
STANDARD FLOW OF DIAGNOSTIC
TROUBLESHOOTING
M1541501400141
Refer to GROUP 00
− Contents of troubleshooting .
TROUBLE SYMPTOM CHART
M1541500700332
Trouble symptom
Reference page
The hazard warning lamps do not illuminate.
SYMPTOM PROCEDURES
The hazard warning lamps do not illuminate.
CAUTION
• Before replacing the ECU, ensure that the
power supply circuit, the earth circuit and the
communication circuit are normal.
• When the ETACS-ECU of vehicles without
KOS is replaced, the encrypted code of the
ignition key needs to be registered to the
ETACS-ECU. (If the encrypted code is not reg-
istered, the engine cannot be started. Regis-
ter the encrypted code as described in
Immobilizer System
− How to Register Key ID
COMMENTS ON TROUBLE SYMPTOM
If the hazard warning lamps do not illuminate, the
hazard warning lamp switch input circuit in centre
panel unit or the ETACS-ECU may have a problem.
PROBABLE CAUSES
• Malfunction of centre panel unit
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
STEP 1. Check that the turn-signal lamps
operate.
Check that the turn-signal lamps illuminate normally.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Diagnose the headlamps. Refer to
Inspection Procedure 10 "The turn-signal
lamps do not illuminate"
.
STEP 2. M.U.T.-III data list
Using the ETACS-ECU service data, check the haz-
ard warning lamp signal.
•
Item No.
Item name
Normal
condition
Item 265
Hazard switch
ON
Turn ON the hazard lamp switch.
OK: Normal condition is displayed.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Troubleshoot the ETACS-ECU. Refer to
Inspection Procedure 10 "The hazard
warning lamp switch signal is not received"
.
STEP 3. Retest the system
Check that the hazard warning lamps illuminate nor-
mally.
Q: Is the check result normal?
MB992006
Extra fine probe
Continuity check and voltage
measurement at harness wire or
connector
Tool
Number
Name
Use
HAZARD WARNING LAMP SWITCH
CHASSIS ELECTRICAL
54A-174
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the ETACS-ECU.
ON-VEHICLE SERVICE
HAZARD WARNING LAMP SWITCH
CHECK
M1541501100311
Using the M.U.T.-III, check the data list of ETACS. It
is judged normal if the display turns ON when the
hazard warning lamp switch is pressed, or OFF when
not pressed for the item No. 265: Hazard switch.
HAZARD WARNING LAMP SWITCH
REMOVAL AND INSTALLATION
M1541501000358
Pre-removal Operation
• Centre Panel Assembly Removal (Refer to GROUP 52A −
Instrument Panel Assembly ).
Post-installation Operation
• Centre Panel Assembly Installation (Refer to GROUP 52A
− Instrument Panel Assembly ).
ACB05534
Hazard warning switch
2.5 ± 0.5 N·m
AB
2.5 ± 0.5 N·m
NOTE
: Claw positions
HORN
CHASSIS ELECTRICAL
54A-175
HORN
ON-VEHICLE SERVICE
HORN RELAY CHECK
M1542100400712
ACB05796
ACB04408
AB
Battery voltage
Terminal
number
Normal
condition
At no energisation
3
− 4
No
continuity
With current supply
[terminal 1 (+), terminal 2
(
−)]
Continuity
exists (2
Ω
or less)
HORN
CHASSIS ELECTRICAL
54A-176
HORN
REMOVAL AND INSTALLATION
M1542100201142
Pre-removal Operation
• Front Bumper Assembly Removal (Refer to GROUP 51 −
Front Bumper Assembly ).
Post-installation Operation
• Front Bumper Assembly Installation (Refer to GROUP 51
− Front Bumper Assembly ).
ACB05663AB
23 ± 9 N·m
1
2
23 ± 9 N·m
Removal steps
>>
A
<<
1.
Horn (HI)
>>
A
<<
2.
Horn (LO)
INSTALLATION SERVICE POINT
>>A<< HORN INSTALLATION
AC805322
Use the earth bolt as the mounting bolt for horn. The
earth bolt has "E" mark on the bolt head.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст