Mitsubishi Outlander (2013+). Manual — part 558
ON-VEHICLE SERVICE <OSS-ECU>
KEYLESS OPERATION SYSTEM (KOS)
42B-93
CHECK OF ENGINE SWITCH INDICATOR
FUNCTION
M1429627100023
Check that the engine switch indicator is switched as
follows in each power supply mode and when an
error is detected.
INDICATOR
Power supply mode and at
error detection
INDICATOR
AC904994AB
Indicator
OFF
Extinguished
ACC
Illuminated in orange
ON
Illuminated in green
ON (after engine start)
Extinguished at 3 seconds after the engine is
started
System error
Flashes in orange
Special operation mode
*
Flashes in green (when ACC and ON only)
NOTE:
*
: The special operation mode indicates that
OSS-ECU is brand new.
CHECK OF ENGINE SWITCH REMINDER
BUZZER
M1429620300026
1. With the driver's door kept closed, release the
steering lock, and then turn the power supply
mode to ACC or ON.
2. Open the driver's door.
3. Check that the buzzer sounds normally.
4. If there is a malfunction, troubleshoot the combi-
nation meter. (Refer to GROUP 54A
− Combina-
tion Meter, Trouble Symptom Chart .)
REGISTRATION WHEN REPLACING
OSS-ECU AND ELECTRIC STEERING
LOCK
M1429627200031
CAUTION
• When KOS-ECU is replaced, all the registra-
tions that need to be performed at KOS-ECU
replacement must be completed before the
registration of OSS-ECU and electric steering
lock.
• Be sure to check that the diagnosis code
No.B1157 OSS EEPROM error and No.B1155
ESL EEPROM error are not set. If the diagno-
sis code No.B1157 "OSS EEPROM error" and
No.B1155 "ESL EEPROM error" are set, the
chassis number cannot be stored in memory
even when it is written. Therefore, when these
diagnosis codes are set, be sure to carry out
the troubleshooting first to repair the trouble,
and then write the chassis number to
OSS-ECU or electric steering lock.
When OSS-ECU or electric steering lock is replaced,
the chassis number needs to be registered to the
replaced ECU.
CHASSIS NUMBER REGISTRATION
PROCEDURE
NOTE: Regardless of which of OSS-ECU or electric
steering lock is replaced, the registration can be per-
formed by executing the same menu selection.
(Even when both OSS-ECU and electric steering
lock were replaced as a set, they can be registered
by performing the registration process only once.)
1. Replace the OSS-ECU or electric steering lock.
ACB05017
MB992747, MB992748, MB991827
MB992744, MB991824
AB
MB992745, MB991910
Diagnosis connector
ON-VEHICLE SERVICE <OSS-ECU>
KEYLESS OPERATION SYSTEM (KOS)
42B-94
2. Connect M.U.T.-III to the diagnosis connector.
3. From the system selection screen of M.U.T.-III,
select "OSS".
4. From the OSS function menu screen, select
"Coding".
AC905137
Please select function.
Chassis No./VIN Writing
Coding
Coding
AD
Chassis No./VIN Information
5. From the coding menu screen, select "Chassis
No./VIN Writing."
AC905138
Coding
Chassis No./VIN Writing
Writing status
ECU Name
Chassis No./VIN
Status
Completed
Completed
Not completed
The Chassis No./VIN is written into blank ECU.
(The same Chassis No./VIN as Engine ECU is written.)
Press OK button to execute.
AF
OK button
AC905139
Chassis No./VIN Writing
Chassis No./VIN Writing will start.
Are you sure?
Caution:
You can write Chassis No./VIN into ECU only once.
AC
Cancel button
OK button
AC905140
Chassis No./VIN Writing
Completed.
AB
6. Following the instruction on the screen, press the
OK button to execute the chassis number writing.
(M.U.T. screen above indicates when OSS-ECU
is replaced.)
AC905141
Coding
Chassis No./VIN Writing
Writing status
ECU Name
Chassis No./VIN
Status
Completed
Completed
Completed
Please confirm the writing result.
AE
7. On the writing result confirmation screen, check
that the chassis number is written, and finish the
registration.
8. Operate the engine switch to turn OFF the power
supply.
KOS-ECU
KEYLESS OPERATION SYSTEM (KOS)
42B-95
NOTE: After the M.U.T.-III has executed the chas-
sis number writing, it will turn the engine switch on
forcibly. Therefore, after completion, turn the
engine switch off.
9. Set the driver's door from open to close or from
close to open.
10.Carrying the keyless operation key, perform the
engine switch operation to turn the power from
OFF to ON twice.
11.Check that the OSS-ECU diagnosis code (B1160,
B1164, B1165, B1166 or U1199) is not set, and
finish the registration.
KOS-ECU
REMOVAL AND INSTALLATION
M1429605900407
CAUTION
If KOS-ECU is replaced, refer to ID code registration need judgement table
to complete the
registration of each ID code.
ACB05639
1
AB
Removal steps
• Upper glove box assembly (Refer
to GROUP 52A
− Instrument panel
assembly .)
• OSS-ECU (Refer to
.)
1. KOS-ECU
Removal steps (Continued)
OUTSIDE TRANSMISSION ANTENNA ASSEMBLY, INSIDE TRANSMISSION ANTENNA
KEYLESS OPERATION SYSTEM (KOS)
42B-96
OUTSIDE TRANSMISSION ANTENNA ASSEMBLY, INSIDE
TRANSMISSION ANTENNA ASSEMBLY
REMOVAL AND INSTALLATION
M1429619300099
AC905335
ACB05641
2
1
3
4
5
6
AB
5.0 ± 2.0 N·m
Outside transmission antenna
assembly (driver’s side)
removal steps
•
Centre pillar trim upper (LH)
(Refer to GROUP 52A
− Interior
Trim .)
1.
Outside transmission antenna
assembly (driver’s side)
Outside transmission antenna
assembly (passenger’s side)
removal steps
•
Centre pillar trim upper (RH)
(Refer to GROUP 52A
− Interior
Trim .)
2.
Outside transmission antenna
assembly (passenger’s side)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст