Mitsubishi Outlander (2013+). Manual — part 567

WINDSHIELD WIPER AND WASHER

EXTERIOR

51-27

Inspection Procedure 3: The windshield wipers do not stop at the specified park position.

CAUTION

Whenever ECU is replaced, ensure that the input and output signal circuits are normal.

COMMENTS ON TROUBLE SYMPTOM

The windshield wiper motor or the ETACS-ECU may
be defective.

PROBABLE CAUSES

• Defective windshield wiper motor

• Malfunction of ETACS-ECU

• Malfunctions of the wiring harness and connec-

tors

DIAGNOSTIC PROCEDURE

STEP 1. Check the windshield wiper motor.
Check that the windshield wiper motor works nor-
mally. Refer to

P.51-42

.

Q: Is the check result normal?

YES :

Go to Step 2.

NO :

Replace the windshield wiper motor.

STEP 2. Measure the voltage at windshield wiper
motor connector.
(1) Disconnect the connector, and measure the

voltage at the wiring harness side.

(2) Set the ignition switch to the ACC position.
(3) Measure the voltage between the windshield

wiper motor connector (ACC terminal) and the
body earth.

OK: System voltage

Q: Is the check result normal?

YES :

Go to Step 4.

NO :

Go to Step 3.

STEP 3. Check of open, short circuit in power
supply line between windshield wiper motor
connector and ignition switch (ACC).

Q: Is the check result normal?

YES :

The trouble can be an intermittent

malfunction (Refer to GROUP 00, How to
use Troubleshooting/inspection Service
Points

− How to Cope with Intermittent

Malfunction ).

NO :

Repair the connector(s) or wiring harness

STEP 4. Check of open, short circuit in W.AS,
WACC line between windshield wiper motor
connector and ETACS-ECU connector

Q: Is the check result normal?

YES :

Go to Step 5.

NO :

Repair the connector(s) or wiring harness

STEP 5. Retest the system.
Check that the windshield wipers stop at the speci-
fied park position.

Q: Is the check result normal?

YES :

Intermittent malfunction (Refer to GROUP

00

− How to Use

Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunction ).

NO :

Replace the ETACS-ECU.

Inspection Procedure 4: The windshield wipers do not work normally.

CAUTION

Whenever ECU is replaced, ensure that the input and output signal circuits are normal.

COMMENTS ON TROUBLE SYMPTOM

The windshield wiper motor, the column switch or the
ETACS-ECU may be defective.

PROBABLE CAUSES

• Defective windshield wiper motor

• Defective column switch (column-ECU)

• Malfunction of ETACS-ECU

• Malfunctions of the wiring harness and connec-

tors

DIAGNOSTIC PROCEDURE

STEP 1. M.U.T.-III diagnosis code
Check if an ETACS-related diagnosis code is set.

Q: Is the diagnosis code set?

YES :

Troubleshoot the ETACS. (Refer to GROUP

54A

− ETACS, Trouble Symptom Chart .)

NO :

Go to Step 2.

WINDSHIELD WIPER AND WASHER

EXTERIOR

51-28

STEP 2. M.U.T.-III data list
Check the input signal related to the windshield wiper
operation.

• Turn the ignition switch to the ACC position.

•

Item No.

Item name

Windshield
wiper
switch
position

Normal
condition

Item 235

Front wiper
ACT

LO

ON

HI

INTO

ON and
OFF

MIST

ON

Item 236

Front wiper
Lo/Hi

LO

OFF

HI

ON

INTO

OFF

MIST

ON

Operate the windshield wiper switch at each
switch position.

OK: Normal condition is displayed.

Q: Is the check result normal?

YES <Normal conditions are displayed for all
items> :

Go to Step 3.

NO <Normal condition is not displayed for item
Nos. 235 and/or 236> :

Troubleshoot the

ETACS-ECU. Refer to ETACS, Diagnosis -
Inspection Procedure 11 "Column switch
signal is not received." .

STEP 3. Check that the windshield wipers work.
Check that the windshield wipers work at high speed
and the mist mode.

Q: Is the check result normal?

YES :

Go to Step 4.

NO :

Go to Step 8.

STEP 4. Check the windshield wiper motor.
Check that the windshield wiper motor works nor-
mally (Refer to

P.51-42

).

Q: Is the check result normal?

YES :

Go to Step 5.

NO :

Replace the windshield wiper motor.

STEP 5. Measure the voltage at windshield wiper
motor connector.
(1) Disconnect the connector, and measure the

voltage at the wiring harness side.

(2) Ignition switch: ACC
(3) Windshield wiper switch: LO

(4) Measure the voltage between the windshield

wiper motor connector power supply terminal and
the body earth.

OK: System voltage

Q: Is the check result normal?

YES :

Intermittent malfunction (Refer to GROUP

00

− How to Use

Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunction .)

NO :

Go to Step 6.

STEP 6. Check of open, short circuit in W.LO line
between windshield wiper motor connector and
ETACS-ECU connector.

Q: Is the check result normal?

YES :

Go to Step 7.

NO :

Repair the wiring harness.

STEP 7. Retest the system.
Check that the windshield wipers work normally by
moving the switch to each position.

Q: Is the check result normal?

YES :

Intermittent malfunction (Refer to GROUP

00

− How to Use

Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunction ).

NO :

Replace the ETACS-ECU.

STEP 8. Measure the voltage at windshield wiper
motor connector.
(1) Disconnect the connector, and measure the

voltage at the wiring harness side.

(2) Ignition switch: ACC
(3) Windshield wiper switch: HI,MIST
(4) Measure the voltage between the windshield

wiper motor connector power supply terminal and
the body earth.

OK: System voltage

Q: Is the check result normal?

YES :

Intermittent malfunction (Refer to GROUP

00

− How to Use

Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunction ).

NO :

Go to Step 9.

STEP 9. Check of open, short circuit in W.HI line
between windshield wiper motor connector and
ETACS-ECU connector.

Q: Is the check result normal?

YES :

Go to Step 10.

NO :

Repair the connector(s) or wiring harness.

WINDSHIELD WIPER AND WASHER

EXTERIOR

51-29

STEP 10. Retest the system.
Check that the windshield wipers work normally by
moving the switch to each position.

Q: Is the check result normal?

YES :

Intermittent malfunction (Refer to GROUP

00

− How to Use

Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunction ).

NO :

Replace the ETACS-ECU.

Inspection Procedure 5: The windshield intermittent wiper interval cannot be adjusted by operating
the windshield intermittent wiper volume control.

CAUTION

Whenever ECU is replaced, ensure that the input and output signal circuits are normal.

COMMENTS ON TROUBLE SYMPTOM

The column switch or the ETACS-ECU may be
defective.

PROBABLE CAUSES

• Defective column switch (column-ECU)

• Malfunction of ETACS-ECU

• Malfunctions of the wiring harness and connec-

tors

DIAGNOSTIC PROCEDURE

STEP 1. M.U.T.-III diagnosis code.
Check if an ETACS-related diagnosis code is set.

Q: Is the diagnosis code set?

YES :

Troubleshoot the ETACS. (Refer to GROUP

54A

− ETACS, Trouble Symptom Chart .)

NO :

Go to Step 2.

STEP 2. Check the ETACS customisation
function.
Use the ETACS customise function to check that
"Front wiper operation" is set to "variable INT" or
"vehicle speed dependent".

Q: Is the check result normal?

YES :

Go to Step 3.

NO :

Use the ETACS customise function to set
"Front wiper operation" to "variable INT" or
"vehicle speed dependent". Refer to

P.51-37

.

STEP 3. M.U.T.-III data list
Check the input signal related to the windshield wiper
operation.

• Ignition switch: ACC

• Rotate the windshield wiper interval control from

(+) to (

−) side.

Item No.

Display on
M.U.T.-III

Check
conditions

Normal
condition

Item 359

Front wiper
(interval
volume)

Rotate the
windshield
wiper
interval
control
from (+) to
(

−) side.

Value
changes
from 0(+)
to 254 (

−)

Q: Is the check result normal?

YES :

Go to Step 4.

NO :

Replace the column switch.

STEP 4. Retest the system.
Check that the windshield wiper interval changes
when the windshield wiper volume control is rotated.

Q: Is the check result normal?

YES :

Intermittent malfunction (Refer to GROUP

00

− How to Use

Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunction ).

NO :

Replace the ETACS-ECU.

WINDSHIELD WIPER AND WASHER

EXTERIOR

51-30

Inspection Procedure 6: The intermittent wiper interval is not changed according to the vehicle
speed.

CAUTION

Whenever ECU is replaced, ensure that the input and output signal circuits are normal.

OPERATION

The ETACS-ECU calculates the intermittent wiper
interval according to the vehicle speed signal which
is sent by the ABS-ECU <Vehicles without ASC> or
ASC-ECU <Vehicles with ASC>.

COMMENTS ON TROUBLE SYMPTOM

If the intermittent wiper interval does not depend on
the vehicle speed, the input circuit of the vehicle
speed signal (combination meter) and the
ETACS-ECU may be defective. Alternatively, the
vehicle speed-dependent wiper may be set to "disa-
bled" by using the customise function.

PROBABLE CAUSES

• Defective combination meter

• Malfunction of ETACS-ECU

• Damaged wiring harness and connectors

DIAGNOSTIC PROCEDURE

STEP 1. Check the operation of windshield
intermittent wiper volume control.
Check that the windshield intermittent wiper interval
can be adjusted by operating the windshield intermit-
tent wiper volume control.

Q: Is the check result normal?

YES :

Go to Step 2.

NO :

Refer to Inspection Procedure 5 "The
windshield intermittent wiper interval cannot
be adjusted by operating the windshield
intermittent wiper volume control"

P.51-29

.

STEP 2. Check the ETACS customise function.
Use the ETACS customise function to confirm that
"FRONT WIPER OPERATION" is set to "VEHICLE
SPEED DEPENDENT".

Q: Is the check result normal?

YES :

Go to Step 3.

NO :

Use the ETACS customise function to set
"FRONT WIPER OPERATION" to
"VEHICLE SPEED DEPENDENT" (Refer to

P.51-37

).

STEP 3.Check the speedometer.
(1) Connect the M.U.T.-III to the diagnosis connector.
(2) Use the M.U.T.-III to enter simulated vehicle

speed.

• Item No.1: Speedometer (Refer to .)

OK: The speedometer shows that simu-
lated vehicle speed.

Q: Is the check result normal?

YES :

Go to Step 4.

No :

Perform the troubleshooting to the
speedometer (Refer to GROUP 54A

−

Combination Meter, Inspection Procedure 5
"Speedometer does not work." Refer to .)

STEP 4. Retest the system.
Check that the intermittent wiper interval depends on
the vehicle speed.

Q: Is the check result normal?

YES :

Intermittent malfunction (Refer to GROUP

00

− How to Use

Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunction ).

NO :

Replace the ETACS-ECU.

Inspection Procedure 7: The rain sensitive AUTO wiper function does not work at all <Vehicles with
lighting control sensor>.

CAUTION

Whenever ECU is replaced, ensure that the input and output signal circuits are normal.

OPERATION

The raindrops sensitive wiper function automatically
adjusts the wiping speed of windscreen wiper by

detecting the rainfall through lighting control sensor
when the ignition switch is in the ON position and the
column switch is in the AUTO position.