Mitsubishi Outlander (2013+). Manual — part 635
IMMOBILIZER SYSTEM <Vehicles without keyless operation system>
CHASSIS ELECTRICAL
54A-25
Code No.B1A24 Key ID not registered
CAUTION
• When the diagnosis code No. B1A24 is set, be
sure to diagnose the CAN bus line.
• When replacing the ECU, always check that
the communication circuit is normal.
DIAGNOSIS FUNCTION
ETACS-ECU sets the diagnosis code No. B1A24
when the key ID was not registered in it.
JUDGMENT CRITERIA
ETACS-ECU determines that the abnormality is
present, if the ignition key's key ID is not registered in
ETACS-ECU when the ignition switch is turned ON.
PROBABLE CAUSES
• Malfunction of CAN bus line
• Key ID not registered
• Malfunction of ETACS-ECU
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics
Use M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 2
NO :
Repair the CAN bus line (Refer to GROUP
54C
− Troubleshooting ).
STEP 2. Register the key ID and recheck the
diagnosis code.
Register the key ID of the ignition key by which the
diagnosis code is set (Refer to
recheck if the diagnosis code is set.
(1) Insert the ignition key into ignition switch.
Remove the ignition key from the ignition switch,
and then insert the key again. Turn the ignition
switch to the ON position within 2 to 3 seconds.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Replace ETACS-ECU and register the ID
codes (Refer to
NO :
The diagnosis is complete.
Code No.B1A25 Key ID unmatched
CAUTION
• When the diagnosis code No. B1A25 is set, be
sure to diagnose the CAN bus line.
• When replacing the ECU, always check that
the communication circuit is normal.
DIAGNOSIS FUNCTION
ETACS-ECU sets the diagnosis code No. B1A25
when the received key ID is different from the one
registered in it.
JUDGEMENT CRITERIA
ETACS-ECU determines that the abnormality is
present, if the key ID for the ignition key does not
match the one registered in ETACS-ECU when the
ignition switch is turned ON.
PROBABLE CAUSES
• Malfunction of CAN bus line
• Malfunction of the ignition key
• Malfunction of ETACS-ECU
• Accessory key not registered
• Key is registered to another vehicle
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics
Use M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 2
NO :
Repair the CAN bus line (Refer to GROUP
54C
− Troubleshooting ).
STEP 2. Register the key ID and recheck the
diagnosis code.
Register the key ID of the ignition key by which the
diagnosis code is set (Refer to
recheck if the diagnosis code is set.
(1) Insert the ignition key into ignition switch.
Remove the ignition key from the ignition switch,
and then insert the key again. Turn the ignition
switch to the ON position within 2 to 3 seconds.
(2) Check if the diagnosis code is set.
IMMOBILIZER SYSTEM <Vehicles without keyless operation system>
CHASSIS ELECTRICAL
54A-26
Q: Is the diagnosis code set?
YES :
Go to Step 3
NO :
The diagnosis is complete.
STEP 3. Replace the ignition key with another
registered key for the vehicle, and recheck the
diagnosis code.
Replace the ignition key by which the diagnosis code
is set with another ignition key nearby, and recheck if
the diagnosis code is set.
(1) Insert the ignition key into ignition switch.
Remove the ignition key from the ignition switch,
and then insert the key again. Turn the ignition
switch to the ON position within 2 to 3 seconds.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Go to Step 4
NO :
Go to Step 5
STEP 4. Register the key ID and recheck the
diagnosis code.
Register the key ID of the ignition key by which the
diagnosis code is set in Step 3 (refer to
),
and recheck if the diagnosis code is set.
(1) Insert the ignition key into ignition switch.
Remove the ignition key from the ignition switch,
and then insert the key again. Turn the ignition
switch to the ON position within 2 to 3 seconds.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Go to Step 5
NO :
The diagnosis is complete.
STEP 5. Replace the ignition key with a new one,
and recheck the diagnosis code.
Replace the ignition key by which the diagnosis code
is set with a new one, register the key ID of the new
key, (refer to
), and recheck if the diagnosis
code is set.
(1) Insert the ignition key into ignition switch.
Remove the ignition key from the ignition switch,
and then insert the key again. Turn the ignition
switch to the ON position within 2 to 3 seconds.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Replace ETACS-ECU and register the ID
codes (Refer to
NO :
The diagnosis is complete.
Code No.B1A28 Engine
−ECU authentication error
CAUTION
• When the diagnosis code No. B1A28 is set, be
sure to diagnose the CAN bus line.
• When replacing the ECU, always check that
the communication circuit is normal.
DIAGNOSIS FUNCTION
ETACS-ECU sets diagnosis code No. B1A28 when
the ETACS-ECU's key certification result and the
engine-ECU's starting condition do not match.
JUDGEMENT CRITERIA
ETACS-ECU determines that the abnormality is
present, if the key certification result OK but
engine-ECU prohibits engine start by immobilizer
function or key certification result NG but engine per-
mits engine starts.
PROBABLE CAUSES
• Malfunction of CAN bus line
• Malfunction of ETACS-ECU
• Engine-ECU malfunction
• Chassis number registered in engine-ECU
unmatched
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics
Use M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the CAN bus line (Refer to GROUP
54C
− Troubleshooting ).
STEP 2. M.U.T.-III other system diagnosis code
Check whether an engine-related diagnosis code is
set.
Q: Is the diagnosis code set?
YES :
Perform troubleshooting for the engine
(Refer to GROUP 13A
− Troubleshooting ).
NO :
Go to Step 3.
STEP 3. Diagnosis code check
Q: Is diagnosis code No. B1761 or B2206 set?
IMMOBILIZER SYSTEM <Vehicles without keyless operation system>
CHASSIS ELECTRICAL
54A-27
YES :
Proceed to diagnosis code No. B1761 (
Chassis No. not programmed) or diagnosis
code No. B2206 (Chassis No. mismatch)
(Refer to
<B1761>,
<B2206>).
NO :
Go to Step 4.
STEP 4. Check whether the diagnosis code is
reset.
Recheck if the diagnosis code is set.
(1) Once key is removed from the ignition cylinder
and then turn the ignition switch from the LOCK
(OFF) position to the ON position.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Replace ETACS-ECU and register the ID
codes (Refer to
). Then go to Step
5.
NO :
The diagnosis is complete.
STEP 5. Check whether the diagnosis code is
reset.
Recheck if the diagnosis code is set.
(1) Turn the ignition switch from the LOCK (OFF)
position to the ON position.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Replace the engine-ECU and register the
chassis number and key codes [Refer to
GROUP 00
− How to Perform Chassis
Number (Chassis No.) Writing ].
NO :
The diagnosis is complete.
Code No.B1A35 Transponder read error
CAUTION
• When the diagnosis code No. B1A35 is set, be
sure to diagnose the CAN bus line.
• When replacing the ECU, always check that
the communication circuit is normal.
DIAGNOSIS FUNCTION
ETACS-ECU sets the diagnosis code No. B1A35
when it cannot receive data from the transponder.
JUDGEMENT CRITERIA
ETACS-ECU determines that the abnormality is
present, if it cannot receive the key ID for the ignition
key when the ignition switch is turned ON.
PROBABLE CAUSES
• Malfunction of CAN bus line
• Malfunction of the ignition key
• Malfunction of receiver antenna
• Malfunction of ETACS-ECU
• Interference of the key ID
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics
Use M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the CAN bus line (Refer to GROUP
54C
− Troubleshooting ).
STEP 2. Check the ignition key inserted in the
key cylinder for interference.
Q: Are there other ignition keys or anything that
interferes with the communication (things that
generate radio waves such as magnets or
air-cleaning device that has a power plug) near the
ignition key inserted in the key cylinder?
YES :
Move away or remove other ignition keys or
anything that interferes with the
communication, and go to Step 3.
NO :
Go to Step 3.
STEP 3. Check whether the diagnosis code is
reset.
Recheck if the diagnosis code is set.
(1) Turn the ignition switch from the LOCK (OFF)
position to the ON position.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Go to Step 4.
NO :
The diagnosis is complete.
STEP 4. Replace the ignition key with another
registered key for the vehicle, and recheck the
diagnosis code.
Replace the ignition key by which the diagnosis code
is set with another ignition key nearby, and recheck if
the diagnosis code is set.
(1) Turn the ignition switch from the LOCK (OFF)
position to the ON position.
IMMOBILIZER SYSTEM <Vehicles without keyless operation system>
CHASSIS ELECTRICAL
54A-28
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Go to Step 5.
NO :
Go to Step 6.
STEP 5. Register the key ID and recheck the
diagnosis code.
Register the key ID of the ignition key by which the
diagnosis code is set in Step 4 (refer to
),
and recheck if the diagnosis code is set.
(1) Turn the ignition switch from the LOCK (OFF)
position to the ON position.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Go to Step 6.
NO :
The diagnosis is complete.
STEP 6. Replace the ignition key with a new one,
and recheck the diagnosis code.
Replace the ignition key by which the diagnosis code
is set with a new one, register the key ID of the new
key, (refer to
), and recheck if the diagnosis
code is set.
(1) Turn the ignition switch from the LOCK (OFF)
position to the ON position.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Go to Step 7.
NO :
The diagnosis is complete.
STEP 7. Replace the receiver antenna, and
recheck the diagnosis code.
Replace the receiver antenna, register the key ID of
the new key (refer to
), and recheck if the
diagnosis code is set.
(1) Turn the ignition switch from the LOCK (OFF)
position to the ON position.
(2) Check if the diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Replace ETACS-ECU and register the ID
codes (Refer to
NO :
The diagnosis is complete.
Code No.B2352 Antenna fail
CAUTION
When replacing the ECU, always check that the
communication circuit is normal.
DIAGNOSIS FUNCTION
ETACS-ECU sets the diagnosis code No. B2352
when open or short circuit to the earth in the antenna
at the key reminder switch is detected.
JUDGMENT CRITERIA
When during the transponder communication, the
antenna at the key reminder switch (immobilizer
antenna) malfunction is found, ETACS-ECU deter-
mines that the abnormality is present.
PROBABLE CAUSES
• Malfunction of key reminder switch (open circuit
of immobilizer antenna)
• Damaged wiring harness and connectors
• Malfunction of receiver antenna
• Malfunction of ETACS-ECU
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III data list
Check the ETACS-ECU service data.
•
Item No.
Item name
Normal
condition
Item 264
Handle lock switch
Key in
Turn the ignition switch to the OFF (key inserted)
position.
OK: Normal condition is displayed.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to GROUP 54A
− Inspection
Procedure 3: "Key reminder switch signal is
not received
STEP 2. Resistance measurement at the receiver
antenna connector (ANTP, ANTG line).
(1) Disconnect the connector and measure the
resistance at the wiring harness side.
(2) Insert the ignition key into ignition switch.
(3) Measure the resistance between the receiver
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст