Mitsubishi Outlander (2013+). Manual — part 9
BODY DIMENSIONS AND MEASUREMENT METHODS
BODY DIMENSIONS
2-2
BODY DIMENSIONS AND MEASUREMENT METHODS
M4020001000448
•
Type A (projected dimensions) is the dimension
when a measurement location is projected onto
the plane.
NOTE: The height indicates a distance from the
assumed standard line established 100 mm
below the lowest measurement point.
•
Type B (actual-measurement dimensions) is the
actual distance between the measurement
points. Measure using a tracking gauge or a
measuring tape, etc.
NOTE:
.
•
Make the lengths of the tracking gauge
probes the same (A=A’).
•
Do not bend or twist the measuring tape.
•
Insert the tracking gauge probes securely into the
measurement holes.
• When the standard dimensions in the illustration
are enclosed by rectangle, this indicates that the
symmetrical left and right positions have the
same dimensions.
•
When using a notch for dimension measurement, set
the measuring point at the centre of the outer
panel notch.
• The body centre points are shown for the pur-
pose of checking the position of the left and right
symmetry location.
AB302138
AE
Probe
Height
Projected dimension
AB302139
AE
A'
A
Actual-measured
dimension
AB302140
AF
Centre of hole
AB302141
AD
TYPE A (PROJECTED DIMENSIONS)
BODY DIMENSIONS
2-3
TYPE A (PROJECTED DIMENSIONS)
UNDER BODY
M4020005002598
ABB00759AB
Unit: mm
Centre line of the vehicle
1
12
6
11
5
10
4
9
3
8
2
7
976
1262
960
1022
910
1056
875
1050
894
894
877
711
540
510
564
624
375
462
350
374
440
393
582
701
833
752
962
197
171
ABB00760AB
Centre line of the vehicle
1
12
6
11
5
10
4
9
3
8
2
7
1180
1394
1079
1028
1138
1272
1216
1126
1342
1218
1416
1025
1125
983
763
641
544
960
686
Unit: mm
No.
Standard measurement point
Hole shape
Size mm
1*
Centre of front end side panel mounting hole
Round
16
2*
Centre of front sidemember inner positioning hole
Round
25
3*
Centre of front axle crossmember mounting hole
Round
15.5
4*
Centre of front sidemember rear water draining hole
Round
16
5
Centre of propeller shaft assembly mounting hole (left side)
Round
11
6
Centre of propeller shaft assembly mounting hole (right side)
Round
11
7*
Centre of front floor sidemember front positioning hole
Round
16
8*
Centre of front floor sidemember front positioning hole
Round
16
9*
Centre of rear floor sidemember lower positioning hole
Oblong
33.9
×18
10*
Centre of rear suspension bracket front water draining hole
Round
16
TYPE A (PROJECTED DIMENSIONS)
BODY DIMENSIONS
2-4
NOTE: The * mark indicates the mounting position for the frame centring gauge.
11*
Centre of rear floor sidemember lower positioning hole
Round
25
12*
Centre of trailer hitch mounting hole
Round
11
No.
Standard measurement point
Hole shape
Size mm
ABB00756AB
Unit: mm
NOTE: The assumed standard line is established 100 mm below the measurement point No.4.
1
12
6
11
5
10
4
9
3
8
2
7
347
187
294
100
259
157
286
105
354
105
358
154
510
1220
486
1049
1136
716
1712
350
326
750
ABB00743
AB
2
1
1, 2
ABB00745
AB
3
ABB00943
AB
4
ABB00747
AB
5
6
5, 6
ABB00748
AB
7
ABB00749
AB
9
8
8, 9
TYPE A (PROJECTED DIMENSIONS)
BODY DIMENSIONS
2-5
SUSPENSION INSTALLATION
DIMENSIONS
M4020013002463
ABB00940
AB
10
11
10, 11
ABB00752
AB
12
ABB00761
AB
Centre line of the vehicle
Unit: mm
15
14
17
16
13
4
3
8
18
19
910
1288
1129
875
1092
1093
894
1000
886
903
293
217
510
579
254
441
714
603
822
289
694
98
ABB00762
AB
Centre line of the vehicle
15
14
17
16
13
4
3
8
1028
1231
1253
1171
1145
1212
1075
945
907
1294
1047
Unit: mm
No.
Standard measurement point
Hole shape
Size mm
3
Centre of front axle crossmember mounting hole
Round
15.5
4
Centre of front sidemember rear water draining hole
Round
16
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст