Mitsubishi Outlander (2013+). Manual — part 584
HEADLINING
INTERIOR
52A-16
HEADLINING
REMOVAL AND INSTALLATION
M1521001402032
CAUTION
For the removal of the headlining, refer to GROUP 52B
− Service Precautions (Refer to ) and Curtain
Air Bag Module (Refer to ).
Pre-removal and Post-installation Operation
• Removal and Installation of Front Pillar Trim, Rear scuff
plate, Front scuff plate, Cowl side Trim, Upper centre Pil-
lar Trim, Lower centre Pillar Trim, Front door opening
Trim, Rear door opening Trim, Quarter trim Lower, Quar-
ter trim Upper, Rear end Trim, Rear Pillar Trim (Refer to ).
• Removal and Installation of Rear Seatbelt Outer Assem-
bly (RH or LH) (Refer to ).
• Removal and Installation of Front door Assembly (RH)
(Refer to GROUP 42A-door Assembly ).
• Removal and Installation of Instrument panel assembly
(Refer to ).
• Removal and Installation of Front Seat Assembly (Refer
to ).
• Removal and Installation of Parking brake lever assembly
(Refer to GROUP 37-Parking brake assembly ).
• Removal and Installation of Centre flame assembly (Refer
to GROUP 55A-Heater unit and blower assembly ).
ACB05041
11
1
3
3
4
4
2
8
AB
6
A
1
12
8
9
7
Section A – A
2
Clip
Claw
A
5
10
Removal steps
1.
Assist grip
•
Front room lamp connector
•
Sunroof switch connector <Vehicles
with sunroof>
2.
Front room lamp assembly
3.
Sunvisor
<<
A
>>
4.
Sunvisor holder
5.
Rear Seatbelt Outer cover
6.
Sunroof lid inner weather strip rear
<Vehicles with sunroof>
<<
B
>>
7.
Headlining
8.
Assist grip bracket
9.
Rear room lamp bracket
10. Rear room lamp assembly
11. Cargo room lamp bracket
12. Cargo room lamp assembly
HEADLINING
INTERIOR
52A-17
REMOVAL SERVICE POINTS
<<A>> SUNVISOR HOLDER REMOVAL
AC005512
MB990784
MB990784
AC
Sunvisor holder
Insert the special tools ornament remover
(MB990784) into the sunvisor holder from its left and
right sides to disengage the claws on the sunvisor
holder sides.
INSIDE REAR VIEW MIRROR
INTERIOR
52A-18
<<B>> HEADLINING ASSEMBLY
REMOVAL
AC600751AC
Clip
Headlining
Vinyl cord
1. To remove the clip, insert a vinyl cord into a
clearance between the clip and the headlining,
and pass it around the clip. Then, pull out the clip
downwards while pulling the vinyl cord.
ACB05043 AB
Headlining
2. Take out the headlining assembly through the
front passenger's door opening.
INSIDE REAR VIEW MIRROR
ADHESIVE
M1521000500193
Application
Brand name
Inside rear view mirror
Inside rear view mirror adhesive kit MU-150Kit
[MZ100425]
NOTE: The symbol in parentheses indicates a part
number.
REMOVAL AND INSTALLATION
M1521002600839
REMOVAL SERVICE POINT
<<A>> INSIDE REAR VIEW MIRROR
REMOVAL
1.
AC209066AB
Claw A
1
3
2
Claw B
Cover
Disengage the claw A and lower the cover toward
arrow 1 direction.
2. Push the claw B toward arrow 2 direction to
unlock, and pull out the mirror toward arrow 3
direction.
SEAT ASSEMBLY
INTERIOR
52A-19
SEAT ASSEMBLY
FRONT SEAT ASSEMBLY
REMOVAL AND INSTALLATION
M1522001302180
CAUTION
Before removing the front seat assembly, refer to GROUP 52B, Service Precautions and Side Airbag
Module (s) .
ACB05055
1
1
4
3
3
3
2
2
3
4
43 ± 8 N·m
AB
43 ± 8 N·m
43 ± 8 N·m
43 ± 8 N·m
43 ± 8 N·m
43 ± 8 N·m
Removal steps
1.
Headrestraint
2.
Front seat anchor cover
3.
Rear seat anchor cover
<<
A
>>
•
Wiring harness connectors
connection
>>
A
<<
4.
Front seat assembly
REMOVAL SERVICE POINT
<<A>> WIRING HARNESS CONNECTOR
DISCONNECTION
ACC00466
AB
D-18
D-21
D-20
D-19
D-22
D-23
D-24
Disconnect the following wiring harness connectors:
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст