Mitsubishi Outlander (2013+). Manual — part 677

REVERSING SENSOR (CORNER SENSOR AND BACK SENSOR)

CHASSIS ELECTRICAL

54A-193

SONAR SWITCH (CORNER SENSOR
SWITCH)

REMOVAL AND INSTALLATION

M1544302300034

Pre-removal Operation
• Instrument Panel Lower Removal (Refer to GROUP 52A

− Instrument Panel Assembly ) <Vehicles without Knee
Air Bag>.

• Instrument Panel Lower LH Removal (Refer to GROUP

52A

− Instrument Panel Assembly ) <Vehicles with Knee

Air Bag>.

Post-installation Operation
• Instrument Panel Lower Installation (Refer to GROUP

52A

− Instrument Panel Assembly ) <Vehicles without

Knee Air Bag>.

• Instrument Panel Lower LH Installation (Refer to GROUP

52A

− Instrument Panel Assembly ) <Vehicles with Knee

Air Bag>.

ACB05547

Sonar switch

AB

SONAR SWITCH CHECK

M1540701800270

ON/OFF CHECK

ACB05548

AB

Indicator

Switch position

Terminal
number

Normal
condition

ON (switch pushed)

10

− 13

Continuity
exists (2

Ω

or less)

OFF (switch released)

No
continuity

INDICATOR CHECK

Apply the battery voltage to the connector terminal
No. 9, earth the terminal No. 14, and then check that
the indicator illuminates.

ACCESSORY SOCKET AND CIGARETTE LIGHTER

CHASSIS ELECTRICAL

54A-194

ACCESSORY SOCKET AND CIGARETTE LIGHTER

SPECIAL TOOLS

M1542300700104

Tool

Number

Name

Use

ACB05421

MB992745

MB992746

MB992744

MB992747

MB992748

a

b

c

d

e

DO NOT USE

AB

a. MB992744
b. MB992745
c. MB992746
d. MB992747
e. MB992748

a. Vehicle

communication
interface-Lite
(V.C.I.-Lite)

b. V.C.I.-Lite main

harness A (for
vehicles with CAN
communication)

c. V.C.I.-Lite main

harness B (for
vehicles without
CAN
communication)

d. V.C.I.-Lite USB

cable short

e. V.C.I.-Lite USB

cable long

M.U.T.-III diagnosis code display,
service data display

MB991910

MB991826

MB991955

MB991911

MB991824

MB991827

MB991825

a

b

c

d

e

f

DO NOT USE

ACCESSORY SOCKET AND CIGARETTE LIGHTER

CHASSIS ELECTRICAL

54A-195

MB991955

a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991825
f. MB991826

M.U.T.-III
sub-assembly

a. Vehicle

communication
interface (V.C.I.)

b. M.U.T.-III USB

cable

c. M.U.T.-III main

harness A (for
vehicles with CAN
communication)

d. M.U.T.-III main

harness B (for
vehicles without
CAN
communication)

e. Measuring adapter

harness

f. M.U.T.-III trigger

harness

CAUTION

For vehicles with CAN
communication, use M.U.T.-III
main harness A to send the
simulated vehicle speed. If you
connect M.U.T.-III main harness
B instead, CAN communication
does not function correctly.
M.U.T.-III diagnosis code display,
service data display

MB991223

a

d

c

b

DO NOT USE

BA

MB991223

a. MB991219
b. MB991220
c. MB991221
d. MB991222

Wiring harness set

a. Check harness
b. LED harness
c. LED harness

adapter

d. Probe

Continuity check and voltage
measurement at wiring harness or
connector

a. For checking connector pin

contact pressure

b. For checking power supply

circuit

c. For checking power supply

circuit

d. For connecting a locally

sourced tester

Tool

Number

Name

Use

MB992006

ACCESSORY SOCKET AND CIGARETTE LIGHTER

CHASSIS ELECTRICAL

54A-196

TROUBLESHOOTING

STANDARD FLOW OF DIAGNOSTIC
TROUBLESHOOTING

M1542301100020

Refer to GROUP 00

− Contents of troubleshooting .

TROUBLE SYMPTOM CHART

M1542300800242

Inspection
Procedure No.

Trouble symptom

Reference
page

1

The accessory socket does not work.

P.54A-196

2

The cigarette lighter does not work.

P.54A-197

SYMPTOM PROCEDURES

Inspection Procedure 1: The accessory socket does not work.

CAUTION

Before replacing the ECU, ensure that the power
supply circuit, the earth circuit and the communi-
cation circuit are normal.

OPERATION

When the ignition switch is in the ON or ACC posi-
tion, the accessory socket can be used.

NOTE: The maximum load of accessory socket is
120 W.

COMMENTS ON TROUBLE SYMPTOM

If the accessory socket cannot be used even when
the ignition switch is in the ON or ACC position,
ETACS-ECU, accessory socket itself, or accessory
socket power supply circuit may have a problem.

PROBABLE CAUSES

• Malfunctions of accessory socket

• Malfunction of the ETACS-ECU

• Damaged harness wires and connectors

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III other system diagnosis code
Check if the diagnosis code is set to the
ETACS-ECU.

Q: Is the check result normal?

YES :

Troubleshoot the ETACS-ECU. Refer to

ETACS-ECU

− Troubleshooting

P.54A-312

.

NO :

Go to Step 2.

STEP 2. M.U.T.-III other system data list
Check the input signal of ACC relay. (ETACS-ECU)

•

Item No.

Item name

Normal
condition

Item 288

ACC switch

ON

Turn the ignition switch to the ACC position.

OK: Normal condition is displayed.

Q: Is the check result normal?

YES :

Go to Step 3.

NO :

Refer to ETACS

− Input Signal Procedure 1

"The ignition switch (ACC) signal is not
received"

P.54A-312

.

STEP 3. Voltage measurement at accessory

socket connector (ASK2 terminal).
(1) Disconnect the connector, and measure at the

MB992006

Extra fine probe

Continuity check and voltage
measurement at wiring harness or
connector

Tool

Number

Name

Use