Mitsubishi Outlander (2013+). Manual — part 338

WATER HOSE AND WATER PIPE

ENGINE COOLING

14-18

Specified sealant: ThreeBond 1324N or
equivalent

NOTE: Install the engine coolant temperature
sensor immediately after applying sealant.

CAUTION

After the installation, until a sufficient period of
time (one hour or more) elapses, do not apply the
oil or water to the sealant application area or
start the engine.

AC509216

MB992042

AB

2. Use special tool water temp sensor wrench

(MB992042) to tighten the engine coolant
temperature sensor to the specified torque.

Tightening torque: 30

± 9 N⋅m

>>C<< RADIATOR UPPER HOSE/HOSE
CLIP CONNECTION

CAUTION

Never reuse the hose clip whose claw is broken
off to prevent the rusting.

1. Make mating mark on a new hose clip in the same

position as the remove one.

AC606082

Water outlet fitting

AX

Protrusion

Mating marks

2. Insert the radiator upper hose until the protrusion

of the water outlet fitting.

3. Align the mating marks on the radiator upper hose

and hose clip.

4. Remove the hose clip claw and shorten the hose

clip, then install the radiator upper hose.

INSPECTION

M1141003400876

WATER PIPE AND HOSE CHECK

Check the water pipe and hose for cracks, damage
and clogs. Replace them if necessary.

RADIATOR

ENGINE COOLING

14-19

RADIATOR

REMOVAL AND INSTALLATION

M1141001503940

Pre-removal Operation
• Front under cover panel and front extension under cover

panel removal (Refer to GROUP 51

− Under Cover ).

• Engine coolant draining (Refer to

P.14-9

).

• Air Cleaner assembly removal (Refer to GROUP 15 − Air

Cleaner ) .

Post-installation Operation
• Air cleaner assembly installation (Refer to GROUP 15 −

Air Cleaner ) .

• Engine coolant refilling (Refer to

P.14-9

).

• Front under cover panel and front extension under cover

panel installation (Refer to GROUP 51

− Under Cover ).

ACB05949

3.4 ± 0.5 N·m

4.4 ± 0.5 N·m

5

6

10

3

12

19

20

1

16

14

22

21

23

26

25

7

AB

N

18

6.9 ± 1.0 N·m

21

8

19

17

11

2

13

N

N

N

4

9

N

3.4 ± 0.5 N·m

15

4.4 ± 0.5 N·m

27

10 ± 4 N·m

24

Removal steps

1.

Radiator drain plug

2.

O-ring

3.

Radiator cap

4.

Radiator condenser tank hose

5.

Radiator condenser tank

6.

CVT fluid cooler feed hose

7.

CVT fluid cooler return hose

<<

A

>>

>>

A

<<

8.

Hose clip

<<

A

>>

>>

A

<<

9.

Radiator upper hose

10. Water pipe

Removal steps (Continued)

RADIATOR

ENGINE COOLING

14-20

REMOVAL SERVICE POINTS

<<A>> HOSE CLIP/RADIATOR HOSE
REMOVAL

AC606081

Mating marks

AE

1. Make mating marks on the radiator hose and the

hose clip as shown to install them in the original
position.

AC302615

Hose clip

Claw (Tip)

AE

2. Break off the tip of hose clip claw and spread out

the hose clip, then disconnect the radiator hose.

NOTE: If there is a hose clip claw, the hose clip
cannot spread to capacity because the claw con-
tacts the hose clip.

INSTALLATION SERVICE POINTS

>>A<< RADIATOR HOSE/HOSE CLIP
CONNECTION

CAUTION

Never reuse the hose clip whose claw is broken
off to prevent the rusting.

1. Make mating mark on a new hose clip in the same

position as the remove one.

AC606082

Protrusion

Pipe, fitting, or etc.

AU

Mating marks

2. Insert the radiator hose until the protrusion of the

pipe.

3. Align the mating marks on the radiator hose and

hose clip.

4. Remove the hose clip claw and shorten the hose

clip, then install the radiator hose.

<<

A

>>

>>

A

<<

11. Hose clip

<<

A

>>

>>

A

<<

12. Radiator upper hose

<<

A

>>

>>

A

<<

13. Hose clip

<<

A

>>

>>

A

<<

14. Radiator lower hose
15. Water pipe

<<

A

>>

>>

A

<<

16. Hose clip

<<

A

>>

>>

A

<<

17. Radiator lower hose
•

Radiator fan motor connector
connection

•

Condenser fan motor connector
connection

18. Fan, fan motor and fan shroud

assembly

•

Front end upper bar assembly
(Refer to GROUP 42A

− Loose

Panel )

19. Support upper insulator
•

Condenser assembly (Refer to
GROUP 55

− Condenser

Assembly

20. Radiator assembly
21. Support lower insulator
22. Radiator fan
23. Radiator fan motor
24. Condenser fan
25. Condenser fan motor
26. Fan shroud
27. Radiator hose support

Removal steps (Continued)

15-1

GROUP 15

INTAKE AND

EXHAUST

CONTENTS

SERVICE SPECIFICATIONS. . . . . . .

15-2

SPECIAL TOOL . . . . . . . . . . . . . . . . .

15-2

AIR CLEANER . . . . . . . . . . . . . . . . . .

15-2

REMOVAL AND INSTALLATION . . . . . . . .

15-2

INLET MANIFOLD . . . . . . . . . . . . . . .

15-4

REMOVAL AND INSTALLATION . . . . . . . .

15-4

INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .

15-6

EXHAUST MANIFOLD . . . . . . . . . . . .

15-7

REMOVAL AND INSTALLATION . . . . . . . .

15-7

INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .

15-8

EXHAUST PIPE AND MAIN MUFFLER

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15-8

REMOVAL AND INSTALLATION . . . . . . . .

15-8