Mitsubishi Outlander (2013+). Manual — part 691
USB
CHASSIS ELECTRICAL
54A-249
REMOVAL AND INSTALLATION
M1549100800465
Pre-removal Operation
• Rear Floor Console Assembly Removal (Refer to GROUP
52A
− Rear Floor Console ).
Post-installation Operation
• Rear Floor Console Assembly Installation (Refer to
GROUP 52A
− Rear Floor Console ).
ACB06033
AB
USB adapter
USB ADAPTER CHECK
M1549101100317
AC900440
AB
Front side
Rear side
1
2
3
4
4
3
2
1
Front side
terminal
Rear side
terminal
Measurement
value
1
1
Continuity
exists (2
Ω or
less)
2
2
3
3
4
4
HANDS FREE ECU
CHASSIS ELECTRICAL
54A-250
HANDS FREE ECU
SPECIAL TOOLS
M1544403500221
Tool
Number
Name
Use
ACB05421
MB992745
MB992746
MB992744
MB992747
MB992748
a
b
c
d
e
DO NOT USE
AB
a. MB992744
b. MB992745
c. MB992746
d. MB992747
e. MB992748
a. Vehicle
communication
interface-Lite
(V.C.I.-Lite)
b. V.C.I.-Lite main
harness A (for
vehicles with CAN
communication)
c. V.C.I.-Lite main
harness B (for
vehicles without
CAN
communication)
d. V.C.I.-Lite USB
cable short
e. V.C.I.-Lite USB
cable long
CAN bus diagnostics or diagnosis
code.
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
a
b
c
d
e
f
DO NOT USE
HANDS FREE ECU
CHASSIS ELECTRICAL
54A-251
MB991955
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991825
f. MB991826
M.U.T.-III
sub-assembly
a. Vehicle
Communication
Interface (V.C.I.)
b. M.U.T.-III USB
cable
c. M.U.T.-III main
harness A
(Vehicles with CAN
communication
system)
d. M.U.T.-III main
harness B
(Vehicles without
CAN
communication
system)
e. M.U.T.-III measure
adapter
f. M.U.T.-III trigger
harness
CAUTION
For vehicles with CAN
communication, use M.U.T.-III
main harness A to send
simulated vehicle speed. If you
connect M.U.T.-III main harness
B instead, the CAN
communication does not
function correctly.
CAN bus diagnostics or diagnosis
code.
MB991223
a
d
c
b
DO NOT USE
BA
MB991223
a. MB991219
b. MB991220
c. MB991221
d. MB991222
Harness set
a. Check harness
b. LED harness
c. LED harness
adapter
d. Probe
Continuity check and voltage
measurement at harness wire or
connector
a. For checking connector pin
contact pressure
b. For checking power supply
circuit
c. For checking power supply
circuit
d. For connecting a locally
sourced tester
Tool
Number
Name
Use
MB992006
HANDS FREE ECU
CHASSIS ELECTRICAL
54A-252
TROUBLESHOOTING
INTRODUCTION TO DIAGNOSIS
M1544404500309
NOTE: For detail of the hands free-ECU, you can see to access via the MITSUBISHI MOTORS web site.
Please read and agree the "Warning about Links to the Web Sites of Other Companies" because it connects
other than MITSUBISHI MOTORS web site. http://www.mitsubishi-motors.com/en/products/index.html
Prior to the troubleshooting, check if the causes below can be the case. If any, take actions according to the
solution method.
Pairing of the Bluetooth
®device (mobile phone or music player) and hands free-ECU cannot be made.
The hands free-ECU does not recognize the Bluetooth
®device (mobile phone or music player)
Cause
Solution
The power of the
bluetooth
®device is off.
With the power of the bluetooth
®device turned on, check the trouble
symptom again.
In addition to the
bluetooth
®device to be
recognized, two or more
bluetooth
®device exist in the
vehicle.
• With the voice operation, select the device to be connected.
• Select the device to be connected on the radio and CD player. <Vehicles
with display audio>
Power supply abnormality in
the hands free-ECU, or
communication error
between the radio and CD
player and hands free-ECU.
Turn the ignition switch to the "ON" position and check if iPod
® connected to
the USB adapter or USB device can be played. If the hands free-ECU is
defective, music cannot be played. Perform the Inspection procedure 2: The
USB adapter data cannot be replayed. (Refer to
.) If the diagnosis
mode of hands free-ECU can be made an entry, the ECU status can be
checked by the hands free-ECU self-check, however, if the power supply of
hands free-ECU, or the communication with the radio and CD player may
have a problem, the ECU status can not be checked. (Refer to
<Vehicles with 1CD audio> or
<Vehicles with display audio>.)
Calling cannot be made using the hands free cellular phone function.
Bluetooth
®The music player cannot be replayed.
The music data received from the USB adapter cannot be replayed.
MB992006
Extra fine probe
Continuity check and voltage
measurement at harness wire or
connector
Tool
Number
Name
Use
Cause
Solution
The Bluetooth
® connection
is not made between the
hands free-ECU and
Bluetooth
®device.
Connect the Bluetooth
®device to the hands free-ECU via Bluetooth®.
The vehicle is not located in
the communication area of
the cellular phone.
Check the radio wave condition of the mobile phone shown on the display, or
check the radio wave condition shown on the mobile phone itself.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст