Mitsubishi Outlander (2013+). Manual — part 666
MB992006
FOG LAMP
CHASSIS ELECTRICAL
54A-149
TROUBLESHOOTING
STANDARD FLOW OF DIAGNOSTIC
TROUBLESHOOTING
M1540401700142
Refer to GROUP 00
− Contents of troubleshooting .
TROUBLE SYMPTOM CHART
M1540401000239
Trouble symptom
Inspection
Procedure No.
Reference page
The front fog lamps do not illuminate normally.
1
One of the front fog lamps does not illuminate.
2
The front fog lamp indicator does not illuminate normally.
3
The rear fog lamp do not illuminate normally.
4
The rear fog lamp indicator does not illuminate normally.
5
SYMPTOM PROCEDURES
Inspection Procedure 1: The front fog lamps do not illuminate normally.
CAUTION
• Before replacing the ECU, ensure that the
power supply circuit, the earth circuit and the
communication circuit are normal.
• When the ETACS-ECU of vehicles without
KOS is replaced, the encrypted code of the
ignition key needs to be registered to the
ETACS-ECU. (If the encrypted code is not reg-
istered, the engine cannot be started. Regis-
ter the encrypted code as described in
Immobilizer System
− How to Register Key ID
CIRCUIT OPERATION
If the front fog lamps do not illuminate normally, the
input signal circuit(s) below or the ETACS-ECU may
be defective.
• Tail lamp switch
• Headlamp switch
• Fog lamp switch
• Option coding information
COMMENTS ON TROUBLE SYMPTOM
When the front fog lamps do not illuminate normally,
the mentioned input signal circuit(s) or ETACS-ECU
may be defective.
PROBABLE CAUSES
• Malfunction of column switch
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
MB992006
Extra fine probe
Continuity check and voltage
measurement at harness wire or
connector
MB990784
MB990784
Ornament
remover
Removal of rear fog lamp assembly
Tool
Number
Name
Use
FOG LAMP
CHASSIS ELECTRICAL
54A-150
DIAGNOSIS PROCEDURE
STEP 1. ETACS-ECU coding data check
(1) Operate the M.U.T.-III to read the ETACS-ECU
option coding information (Refer to GROUP 00
−
Coding Table ).
(2) Check that the "Front fog lamp" is set to
"Present."
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Operate the M.U.T.-III to set the option
coding "Front fog lamp" to "Present," and
check the trouble symptom.
STEP 2. Check the operation of the position
lamps and the headlamps.
Check that the position lamps and the headlamps
illuminate normally.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Check the position lamps and the
headlamps (Refer to trouble symptom chart
).
STEP 3. M.U.T.-III diagnosis code
Check if diagnosis code is set to the ETACS-ECU.
Q: Is the diagnosis code set?
YES :
Troubleshoot the ETACS-ECU. Refer to
.
NO :
Go to Step 4.
STEP 4. M.U.T.-III data list
Use the ETACS-ECU service data to check the sig-
nal related to the operation of front fog lamp function.
•
Item No.
Item name
Normal
condition
Item 345
Fog lamp ON
ON
Turn the fog lamp switch to ON.
OK: Normal condition is displayed.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Troubleshoot the ETACS-ECU. Refer to
Inspection Procedure 11 "The column
switch signal is not received"
.
STEP 5. Check the front fog lamp relay
Refer to
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Replace the front fog lamp relay.
STEP 6. Voltage measurement at front fog lamp
relay connector (power supply terminals).
(1) Remove the front fog lamp relay, and measure at
the relay box side.
(2) Check the voltage between the front fog lamp
relay connector (power supply terminals) and
body earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Go to Step 7.
STEP 7. Check of open circuit in power supply
lines between the front fog lamp relay connector
and fusible link.
Q: Is the check result normal?
YES :
Go to Step 11.
NO :
Repair the connector(s) or wiring harness.
STEP 8. Check of open circuit in FOGY line
between the front fog lamp relay connector and
ETACS-ECU connector.
Q: Is the check result normal?
YES :
Go to Step 9.
NO :
Repair the connector(s) or wiring harness.
STEP 9. Check of open circuit in output line
between the front fog lamp relay connector and
front fog lamp (LH), front fog lamp (RH)
connector.
Q: Is the check result normal?
YES :
Go to Step 10.
NO :
Repair the connector(s) or wiring harness.
STEP 10. Check of open circuit in earth line
between the front fog lamp (LH), front fog lamp
(RH) connector and body earth.
Q: Is the check result normal?
YES :
Go to Step 11.
NO :
Repair the connector(s) or wiring harness.
STEP 11. Retest the system
Check that the front fog lamps illuminate normally.
Q: Is the check result normal?
FOG LAMP
CHASSIS ELECTRICAL
54A-151
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the ETACS-ECU.
Inspection Procedure 2: One of the front fog lamps does not illuminate.
COMMENTS ON TROUBLE SYMPTOM
When one of the front fog lamps does not illuminate,
the wiring harness, connector(s), or bulb(s) may
have a problem, or the fuse may be burned out.
PROBABLE CAUSES
• Malfunction of bulbs
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
STEP 1. Bulb check
Check the bulb(s) of the lamp that does not illumi-
nate.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Replace the bulb(s) of the lamp that does
not illuminate.
STEP 2. Resistance measurement at the front fog
lamp (LH) connector, front fog lamp (RH)
connector (earth terminal).
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Measure the resistance between the connector of
lamp which does not illuminate and the body
earth.
• Measure the resistance between the front fog
lamp (LH) connector (earth terminal) and
body earth.
• Measure the resistance between the front fog
lamp (RH) connector (earth terminal) and
body earth.
OK: Continuity exists (2
Ω or less)
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Go to Step 3.
STEP 3. Check of open circuit in earth line
between the front fog lamp (LH) connector, front
fog lamp (RH) connector and body earth.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the connector(s) or wiring harness.
STEP 4. Check of open circuit in output line
between the front fog lamp relay connector and
front fog lamp (LH), front fog lamp (RH)
connector.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the connector(s) or wiring harness.
STEP 5. Retest the system
Check that the front fog lamps illuminate normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Go to Step 1.
FOG LAMP
CHASSIS ELECTRICAL
54A-152
Inspection Procedure 3: The front fog lamp indicator does not illuminate normally.
CAUTION
• Before replacing the ECU, ensure that the
power supply circuit, the earth circuit and the
communication circuit are normal.
• When the ETACS-ECU of vehicles without
KOS is replaced, the encrypted code of the
ignition key needs to be registered to the
ETACS-ECU. (If the encrypted code is not reg-
istered, the engine cannot be started. Regis-
ter the encrypted code as described in
Immobilizer System
− How to Register Key ID
COMMENTS ON TROUBLE SYMPTOM
If the front fog lamp indicator does not illuminate nor-
mally, connector(s), wiring harness in the CAN bus
lines, the ETACS-ECU or the combination meter may
be defective.
PROBABLE CAUSES
• Malfunction of the ETACS-ECU
• Malfunction of the combination meter
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
STEP 1. Check the front fog lamps
When the front fog lamp switch is operated, check
that the front fog lamps illuminate/go off normally.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
First, repair the front fog lamps (Refer to
trouble symptom chart
).
STEP 2. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Repair the CAN bus line (Refer to GROUP
54C
− Troubleshooting ).
STEP 3. M.U.T.-III diagnosis code
Check if diagnosis code is set to the ETACS-ECU.
Q: Is the diagnosis code set?
YES :
Troubleshoot the ETACS-ECU. Refer to
.
NO :
Go to Step 4.
STEP 4. M.U.T.-III other system special function
Using M.U.T.-III, select "Test" from the special func-
tion of the combination meter. Execute the following
item to check the front fog lamp indicator. (Refer to
Combination Meter
)
• Item 5: Illumination (AUTO)
• Item 6: Indicator (AUTO)
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Troubleshoot the combination meter. Refer
to
STEP 5. Retest the system
Check that the front fog lamp indicator illuminate nor-
mally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the ETACS-ECU.
Inspection Procedure 4: The rear fog lamp do not illuminate normally.
CAUTION
• Before replacing the ECU, ensure that the
power supply circuit, the earth circuit and the
communication circuit are normal.
• When the ETACS-ECU of vehicles without
KOS is replaced, the encrypted code of the
ignition key needs to be registered to the
ETACS-ECU. (If the encrypted code is not reg-
istered, the engine cannot be started. Regis-
ter the encrypted code as described in
Immobilizer System
− How to Register Key ID
CIRCUIT OPERATION
If the rear fog lamps do not illuminate normally, the
input signal circuit(s) below or the ETACS-ECU may
be defective.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст