Mitsubishi Outlander (2013+). Manual — part 579
OUTSIDE MIRROR
EXTERIOR
51-75
(2) Measure the resistance between door mirror
assembly (LH) connector (earth terminal) and
body earth.
OK: Continuity exists (2
Ω or less)
Q: Is the check result normal?
YES :
Go to Step 11.
NO :
Go to Step 10.
STEP 10. Check of open circuit in earth line
between the door mirror assembly (LH)
connector and body earth.
Q: Is the check result normal?
YES :
Intermittent malfunction (Refer to GROUP
00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with
Intermittent Malfunction ).
NO :
Repair the connector(s) or wiring harness.
STEP 11. Measure the voltage at the door mirror
assembly (LH) connector.
(1) Turn the ignition switch to the ON position.
(2) Turn on the rear window defogger switch.
(3) Disconnect the connector, and measure at the
wiring harness side.
(4) Voltage between door mirror assembly (LH)
connector (power supply terminal) and body
earth.
OK: System voltage
Q: Is the check result normal?
YES :
Intermittent malfunction (Refer to GROUP
00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with
Intermittent Malfunction ).
NO :
Go to Step 12.
STEP 12. Check of open circuit DEFO-1&DEFO-2
line between door mirror assembly (LH)
connector and ETACS-ECU connector.
Q: Is the check result normal?
YES :
Go to Step 13.
NO :
Repair the connector(s) or wiring harness.
STEP 13. Retest the system.
Check that the heater element works normally.
Q: Is the check result normal?
YES :
Intermittent malfunction (Refer to GROUP
00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with
Intermittent Malfunction ).
NO :
Replace the door mirror assembly (LH).
ON-VEHICLE SERVICE
CHECK THE VEHICLE
SPEED-DEPENDENT AUTOMATIC
UNFOLDING FUNCTION OF THE
OUTSIDE REAR-VIEW MIRRORS
M1511023300229
1. Check that the outside rear-view mirrors are
unfolded when you set simulated vehicle speed of
30 km/h or more by using the M.U.T.-III with the
mirrors folded.
2. If not, carry out the troubleshooting (Refer to
CHECK THE IGNITION-LIKED FOLD AND
UNFOLDING FUNCTION OF THE
OUTSIDE REAR-VIEW MIRRORS
M1511023400646
1. When the ignition switch is turned on with the
driver's door closed and the door mirrors folded,
the mirrors should be unfolded. When the ignition
switch is turned off and the driver's door is opened
with the mirrors unfolded, they should be folded.
2. If not, carry out the troubleshooting (Refer to
NOTE: The electric folding outside rear-view mirrors
are set to the vehicle speed-dependent unfolding as
default setting. Prior to this check, confirm whether
the ignition-linked function is enabled or not (Refer to
).
DOOR MIRROR KEYLESS ENTRY
FUNCTION OR KOS-LINKED FOLDING
AND UNFOLDING FUNCTION CHECK
M1511023500610
1. When you use the keyless entry system or the
KOS to unlock the doors with the mirrors folded,
they should be unfolded. When the keyless entry
system locks the doors with the mirrors unfolded,
they should be folded.
2. If not, carry out the troubleshooting (Refer to
NOTE: The electric folding outside rear-view mirrors
are set to the vehicle speed-dependent unfolding as
default setting. Prior to this check, confirm whether
the keyless entry system-linked function is enabled
or not (Refer to ).
OUTSIDE MIRROR
EXTERIOR
51-76
CHECK OF DOOR MIRROR TIMER
FUNCTION
M1511021700265
1. Turn the ignition switch to the "LOCK" (OFF)
position. Then check that the door mirrors can be
folded and unfolded for approximately 30
seconds.
2. If not, carry out the troubleshooting (Refer to
CUSTOMISATION FUNCTION
M1511027402310
By operating the M.U.T.-III ETACS system, the fol-
lowing functions can be customised. The pro-
grammed information is held even when the battery
is disconnected.
Adjustment
item (M.U.T.-III
display)
Adjustment item
Adjusting content
(M.U.T.-III display)
Adjusting content
Auto fold mirror
Electric folding door
mirror automatic
unfolding function
<vehicles with
electric retractable
remote controlled
door mirrors>
Not Auto
No synchronised operation
Open Vehicle SPD
Vehicle speed-dependent operation
Open/Close by IG
Ignition switch linked operation
OPN/CLS Keyless
Keyless entry linked operation (initial
condition)
OUTSIDE MIRROR
REMOVAL AND INSTALLATION
M1511006401497
ACB05790
3
AB
1
2
5.0± 1.0 N·m
4
A
B
B
5
ACC00144
View A
Section B – B
: Claw positions
AB
Claw
Claw
2
2
5
ACC00138
3
AB
Claw
Section B – B
Door mirror outer cover claw positions
: Claw positions
C
C
C
C
B
B
B
C
C
C
C
Claw
Section C – C
Claw
Claw
3
3
3
B
B
B
B
B
Door mirror assembly removal
steps
•
Front door delta inner cover (Refer
to GROUP 52A, Door Trim )
•
Front door trim (Refer to GROUP
52A, Door Trim )
•
Door mirror connector connection
1.
Door mirror assembly
Door mirror housing removal
steps
<<
A
>>
2.
Mirror
3.
Door mirror outer cover
4.
Side turn-signal lamp assembly
<With side turn-signal lamp>
5.
Door mirror housing
Remote controlled mirror switch
removal steps
•
Remote controlled mirror switch
(Refer to GROUP 52A, Door Trim .)
OUTSIDE MIRROR
EXTERIOR
51-77
OUTSIDE MIRROR
EXTERIOR
51-78
REMOVAL SERVICE POINT
<<A>> MIRROR REMOVAL
ACB05788 AB
Claw
Claw
Mirror
Door
mirror
housing
CAUTION
The tab of the mirror is prone to breakage when
working in cold temperatures. Always use a hair
drier or the like to warm up the mirror tab and its
periphery to 20
°C or higher prior to works. When
the mirror is heated too quickly from its cold
state, it may be broken.
1. Disengage the tab behind the mirror from the door
mirror housing.
2. Disconnect the connectors of the heated mirror.
INSPECTION
M1511019103704
DOOR MIRROR ASSEMBLY OPERATION
CHECK
Remove the door trim, and then connect the battery
to the door mirror assembly connector to check that
the door mirror operates.
AC708423 AB
Return
Retract
Forward-folding
Battery connection
Operation
direction
• Connect terminal 12 to the negative
battery terminal.
• Connect terminal 5 to the positive
battery terminal.
Up
• Connect terminal 12 to the positive
battery terminal.
• Connect terminal 5 to the negative
battery terminal.
Down
• Connect terminal 13 to the negative
battery terminal.
• Connect terminal 12 to the positive
battery terminal.
Right
• Connect terminal 13 to the positive
battery terminal.
• Connect terminal 12 to the negative
battery terminal.
Left
• Connect terminal 11 to the positive
battery terminal.
• Connect terminal 4 to the negative
battery terminal.
Retract
• Connect terminal 11 to the negative
battery terminal.
• Connect terminal 4 to the positive
battery terminal.
Return
REMOTE CONTROLLED MIRROR
SWITCH CONTINUITY CHECK
AC005970
AC507009
Switch position
Tester
connectio
n
Specified
condition
Left side
Up
1
− 6, 9 −
11
Continuity
exists(2
Ω
or less)
Down
1
− 11, 6 −
9
Right
1
− 6, 9 −
10
Left
1
− 10, 6 −
9
Right side
Up
1
− 6, 3 − 9
Down
1
− 3, 6 − 9
Right
1
− 6, 2 − 9
Left
1
− 2, 6 − 9
Retract and return
1
− 4
Battery connection
Operation
direction
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст