Mitsubishi Outlander (2013+). Manual — part 621
DRIVER'S AIR BAG MODULE AND CLOCK SPRING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-135
INSPECTION
M1524047600280
DRIVER'S AIR BAG MODULE
CAUTION
• Never measure circuit resistance in the air
bag modules (squib) even with the specified
tester. Measuring the circuit resistance with a
tester causes accidental air bag deployment
due to current that flows or static, resulting in
serious personal injury.
• When replacing the parts, discard the old
parts after deploying the air bag according to
the specified procedure (Refer to
If any malfunction is found in the following inspec-
tions, replace the air bag module with a new one.
ACB03701AC
Squib
connectors
Inflator
1. Pad cover dent, crack or deformation
2. Check the harness and connector for damage
and the terminal for deformation.
3. Check the air bag inflator cases for dents, cracks
or deformation.
4. Check the air bag module for proper installation.
CLOCK SPRING
If any malfunction is found in the following inspec-
tions, replace the clock spring with a new one.
AC904942 AG
Case
Clock
spring
connector
Clock spring
connector
Driver's air bag
module connector
Horn connector
Horn connector
Protective tube
1. Check the connectors and protective tubes for
damage and the terminal for deformation.
2. Check the case for damage.
3. Check that the continuity exists between the
following connector terminals.
• Clock spring connector terminal 1 and horn con-
nector terminal 1
• Clock spring connector terminal 5 and horn con-
nector terminal 5
AC905415AC
Clock spring
Digital
multi-meter
Extra fine probe
(MB992006)
4. As shown in the Figure, connect the circuit tester
to special tool extra fine probe (MB992006) and
check to see that there is a charge between the
terminals.
PASSENGER'S (FRONT) AIR BAG MODULE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-136
PASSENGER'S (FRONT) AIR BAG MODULE
REMOVAL AND INSTALLATION
M1524047300386
CAUTION
• Disconnect the negative (−) battery terminal and wait for 60 seconds or more before starting work.
Insulate the disconnected (
−)terminal by wrapping the tape (Refer to the item 5 of Service Precau-
• Never attempt to disassemble or repair the air bag module. If faulty, replace it with new one.
• Do not drop the air bag module or allow contact with water, grease or oil. If denting, cracking, or
deformation is discovered, replace it with new one.
• Store the air bag modules on a flat surface with the deployment surface facing up. Also, do not put
anything on it.
• Do not store the air bag module in a place more than 93°C.
• When the air bags have been deployed, replace the and air bag module with new one.
• Put on gloves and safety glasses when handling deployed air bags.
• When discarding the air bag module, make sure to deploy the air bag before the disposal (Refer to
).
Pre-removal operation
• Turn ignition switch to the LOCK (OFF) position.
• Disconnect the negative (−) battery terminal.
ACB05622
AB
3
2
1
5.0 ± 1.0 N·m
Removal steps
•
Upper glove box assembly (Refer
to GROUP 52A
− Instrument Panel
Assembly ).
<<
A
>>
1.
Passenger’s (front) air bag module
connector
2.
Bolts
•
Instrument panel assembly (Refer
to GROUP 52A
− Instrument Panel
Assembly ).
<<
B
>>
3.
Passenger’s (front) air bag module
Installation steps
>>
A
•
Pre-installation inspection
3.
Passenger’s (front) air bag module
•
Instrument panel assembly (Refer
to GROUP 52A
− Instrument Panel
Assembly ).
2.
Bolts
1.
Passenger’s (front) air bag module
connector
•
Upper glove box assembly (Refer
to GROUP 52A
− Instrument Panel
Assembly ).
>>
B
•
Post-installation inspection
PASSENGER'S (FRONT) AIR BAG MODULE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-137
REMOVAL SERVICE POINTS
<<A>> PASSENGER'S (FRONT) AIR BAG
MODULE CONNECTOR REMOVAL
ACB04307AB
Passenger's air bag module
harness side connector
Locking button
Flat-tipped
screwdriver
Use the flat-tipped screwdriver to pull out the locking
button of wiring harness side connector, and release
the lock.
<<B>> PASSENGER'S (FRONT) AIR BAG
MODULE REMOVAL
CAUTION
• Never use an electric tester to diagnose the
air bag module circuit. Never attempt to dis-
assemble the air bag module.
• The removed passenger's air bag module
should be stored in a clean, dry place with the
deployment surface facing up.
• When discarding the air bag module, discard
after deploying the air bag as specified in the
service procedure (Refer to
ACA00360
Flat-tipped
screwdriver
Passenger's (front)
air bag module
AB
Insert a flat-tipped screwdriver or similar tool to the
location shown in the figure. After disengaging the
tabs, remove the passenger's (front) air bag module.
INSTALLATION SERVICE POINTS
>>A<< PRE-INSTALLATION INSPECTION
1. Before the installation, check the air bag module
(Refer to
NOTE: Even when installing a new air bag mod-
ule, perform an inspection before the installation.
2. Connect the negative (
−) battery terminal.
CAUTION
Be sure to turn the ignition key to the LOCK
(OFF) position when connecting or disconnect-
ing M.U.T.-III.
3. Connect M.U.T.-III to the diagnosis connector (16
pin).
4. Turn the ignition switch to the ON position.
5. Read the diagnosis code, and check that
everything is normal except the air bag module
open circuit.
6. Turn the ignition switch to the LOCK (OFF)
position.
>>B<< POST-INSTALLATION
INSPECTION
1. Connect the negative (
−) battery cable.
2. Turn the ignition switch to the "ON" position.
ACC00038AB
SRS warning lamp
3. Check that the SRS warning lamp is illuminated
for 6 to 8 seconds, and extinguished afterward.
4. If the lamp does not extinguish, perform the
troubleshooting (Refer to
INSPECTION
M1524047400145
CAUTION
• Never measure circuit resistance in the air
bag modules (squib) even with the specified
tester. Measuring the circuit resistance with a
tester causes accidental air bag deployment
due to current that flows or static, resulting in
serious personal injury.
• When replacing the parts, discard the old
parts after deploying the air bag according to
the specified procedure (Refer to
If any malfunction is found in the following inspec-
tions, replace the air bag module with a new one.
ACB05537AB
Squib connectors
Inflator
PASSENGER'S (FRONT) AIR BAG MODULE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-138
1. Check the harness and connector for damage and
the terminal for deformation.
2. Check the air bag inflator cases for dents, cracks
or deformation.
3. Check the air bag module for proper installation.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст