Mitsubishi Montero (1998+). Manual — part 86
Fig. 9: TP Sensor Connector Terminals (All Other Models)
Courtesy of Mitsubishi Motor Sales of America
DEFOGGER - REAR WINDOW
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Rear Window Defoggers
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
DESCRIPTION & OPERATION
Rear window defogger is a heating filament grid bonded to
inside of window. Rear window defogger is controlled by defogger
switch on instrument panel and a defogger relay.
On Montero, a timer relay controls defogger operation for 9-
11 minutes, then turns defogger off. On Eclipse and Galant, defogger
timer circuit is integral with Electronic Timer Alarm Control System
(ETACS) ECU. Timer will operate defogger for 11 minutes then turn off,
even with defogger switch in ON position and indicator light
illuminated. On Diamante, timer will operate defogger for 20 minutes,
then turn off.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE
Component Location
A/C ECU
Diamante . . . . . . . Behind Center Of Dash
Data Link Connector (DLC) . ... Under Left Side Of Dash,
Near Steering Column
Defogger Relay
Montero Sport . . . . . ... Under Left Side Of
Glove Compartment
Except Montero Sport . . . . ... On Relay Block,
Behind Left Side Of Dash
Defogger Timer
Diamante . . . . . . . Integral With A/C ECU
Eclipse & Galant . . . ... Integral With ETACS-ECU
Montero . . . . . .. Behind Left Side Of Dash,
Behind Speaker
ETACS-ECU . . . . . . . Above Left Kick Panel,
On Junction Block
TROUBLE SHOOTING
* PLEASE READ THIS FIRST *
NOTE: For additional trouble shooting information on Eclipse and
Galant, see SYMPTOM TESTS.
DEFOGGER DOES NOT WORK
Check for blown fuse, poor contact, defective defogger
switch, poor connection or open wire.
DEFOGGER TIMER INOPERATIVE
Check defogger switch or defogger timer. See COMPONENT TESTS.
INDICATOR LIGHT DOES NOT WORK
Check for burned out bulb, open circuit or poor connection.
INDICATOR LIGHT IS DIM
Check rheostat or indicator bulb.
SYMPTOM TESTS
INPUT SIGNAL INSPECTION
NOTE: The following information only applies to Eclipse and Galant.
NOTE: Perform input signal inspection before proceeding with
SYSTEM TESTS.
Eclipse & Galant
1) Input signal inspection can be performed using scan tool
or an analog voltmeter. To perform inspection using scan tool, go to
next step. To perform inspection using an analog voltmeter, go to step
3).
2) Turn ignition off. Connect scan tool to Data Link
Connector (DLC). Turn ignition on and then off. If buzzer on scan tool
sounds when ignition was turned on, ECU input signal is normal. If
buzzer did not sound, go to SYSTEM TESTS.
3) Turn ignition off. Connect DTC Check Harness (MB991529) to
DLC terminals No. 4 or 5 (ground) and terminal No. 9. See Fig. 1.
Connect voltmeter leads to check harness leads. Turn ignition switch
on, then off. If voltmeter deflects once when ignition was turned on,
ECU input signal is normal. If voltmeter did not deflect, go to
SYSTEM TESTS.
Fig. 1: Identifying Data Link Connector (DLC) Terminals
Courtesy of Mitsubishi Motor Sales of America
SYSTEM TESTS
NOTE: The following information only applies to Eclipse and Galant.
NOTE: Perform INPUT SIGNAL INSPECTION before proceeding with
SYSTEM TESTS. To identify circuit connector terminals, see
WIRING DIAGRAMS.
Communication With All Systems Not Possible (Eclipse &
Galant)
1) Check voltage between ground and Data Link Connector (DLC)
terminal No. 16 (Red/Black wire on Eclipse or Brown/Red wire on
Galant). See Fig. 1. If battery voltage is present, go to step 3). If
battery voltage is not present, go to next step.
2) Check junction block connectors between DLC and power
supply. See WIRING DIAGRAMS. If connectors are okay, check circuit
between power supply and DLC. See WIRING DIAGRAMS. Repair as
necessary.
3) Check continuity between ground and DLC terminals No. 4
and 5. If continuity is present, replace scan tool and retest. If
continuity is not present, check circuit between ground and DLC. See
WIRING DIAGRAMS. Repair as necessary.
Communication With One-Shot Pulse Input Signal Only Is Not
Possible (Eclipse & Galant)
Check circuit between DLC and junction block No. 1. See
WIRING DIAGRAMS. Repair as necessary. If circuit is okay, check
harness connectors to ETACS-ECU, DLC and junction/joint connectors.
Repair as necessary. If connectors are okay, replace ECU.
Defogger Does Not Operate With Defogger Switch ON (Eclipse &
Galant)
1) Check defogger switch input signal. See
INPUT SIGNAL INSPECTION. If switch input signal is okay, check
defogger circuit and relay. See DEFOGGER RELAY TEST under COMPONENT
TESTS. Repair or replace as necessary. If switch input signal is not
okay, go to next step.
2) Check defogger switch. See DEFOGGER SWITCH TEST under
COMPONENT TESTS. Replace as necessary. If defogger switch is okay,
turn ignition on. Check voltage between ground and defogger switch
harness-side connector terminal No. 4 (Eclipse) or terminal No. 2
(Galant). See WIRING DIAGRAMS. If voltage reading is 5 volts (Eclipse)
or battery voltage (Galant), go to next step. If voltage reading is
not as specified, go to step 4).
3) Check joint/junction connectors between switch, instrument
panel cluster and ETACS-ECU. See WIRING DIAGRAMS. Repair as necessary.
If connectors are okay, check circuit between defogger switch and
ground. Repair as necessary. If circuit is okay, replace ECU.
4) Check harness connectors to ETACS-ECU and instrument panel
cluster. Repair as necessary. If connectors are okay, check circuit
between ECU and defogger switch. Repair as necessary.
Defogger Relay Circuit System Check (Eclipse & Galant)
1) Check defogger relay. See DEFOGGER RELAY TEST under
COMPONENT TESTS. Replace as necessary. If relay is okay, go to next
step.
2) Check voltage between ground and relay harness-side
connector terminals No. 3 and 5. See WIRING DIAGRAMS. If battery
voltage is present, go to next step. If battery voltage is not
present, go to step 4).
3) Check harness connectors to relay, ETACS-ECU, junction
block and rear wiring/liftgate. See WIRING DIAGRAMS. Repair as
necessary. If connectors are okay, check circuit between defogger
relay and rear defogger, defogger and ground, or defogger relay and
ECU. See WIRING DIAGRAMS. Repair as necessary. If circuits are okay,
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст