Mitsubishi Montero (1998+). Manual — part 31
cause accidental air bag deployment and personal injury.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM.
2) Disconnect passenger-side air bag connector C-107. Connect
SRS Check Harness (MB991613) connector No. 1 to passenger-side air bag
connector. Erase DTC memory and check if DTCs 24, 25, or 64 are set.
If any of these DTCs are output, go to next step. If DTCs are not
output, replace passenger-side air bag module. See
PASSENGER-SIDE AIR BAG MODULE under REMOVAL & INSTALLATION.
3) Check connectors C-107 and C-122, and repair if necessary.
If connectors are okay, check trouble symptoms. If fault is still
present, check harness wire between passenger-side air bag module and
SRS-ECU, and repair if necessary. If harness wire is okay, replace
SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL &
INSTALLATION.
DTC 31 & 32: SRS-ECU CAPACITOR SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 34: CONNECTOR LOCK SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
Before proceeding, see SERVICE PRECAUTIONS. Check connector
C-122 and repair if necessary. If connector is okay, check for trouble
symptom. If fault exists, replace SRS-ECU. See
SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 35: SRS-ECU SYSTEM (AFTER AIR BAG DEPLOYMENT)
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 41: IG1 (A) POWER CIRCUIT SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM.
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check terminal No. 20 and 21 for continuity
to ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122 and repair if necessary. If
connector is okay, check for trouble symptom. If fault exists, check
harness wire between SRS-ECU and ground, and repair if necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable and turn ignition switch to ON
position. If voltage between terminal No. 14 and body ground is 9
volts or more, replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU)
under REMOVAL & INSTALLATION. If voltage is not as specified, check
connector C-93, C-101, and C-132, and repair if necessary. If
connectors are okay, check for trouble symptoms. If fault still
exists, check harness wire between SRS-ECU and ignition switch IG1
(A), and repair if necessary.
DTC 42: IG1 (B) POWER CIRCUIT SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM.
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check terminal No. 20 and 21 for continuity
to ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122 and repair if necessary. If
connector is okay, check for trouble symptoms. If fault still exists,
check harness wire between SRS-ECU and ground, and repair if
necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable and turn ignition switch to ON
position. If voltage between terminal No. 13 and body ground is 9
volts or more, replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU)
under REMOVAL & INSTALLATION. If voltage is not as specified, check
connector C-80, C-93, and C-101, and repair if necessary. If
connectors are okay, check for trouble symptoms. If fault still
exists, check harness wire between SRS-ECU and ignition switch IG1
(B), and repair if necessary.
DTC 43: SRS WARNING LIGHT CIRCUIT
NOTE: Refer to WIRING DIAGRAMS for connector identification.
Light Does Not Come On
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM.
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check terminal No. 20 and 21 for continuity
to ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122 and repair if necessary. If
connector is okay, check for trouble symptoms. If fault still exists,
check harness wire between SRS-ECU and ground, and repair if
necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable and turn ignition switch to ON
position. Connect terminal No. 15 to body ground. If SRS warning light
comes on, replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under
REMOVAL & INSTALLATION. If SRS warning light does not come on, inspect
for blown bulb and repair if necessary. If bulb is okay, check
connector C-04, C-11, C-96, and C-101, and repair if necessary. If
connectors are okay, check for trouble symptoms. If fault still
exists, check harness wire between SRS-ECU and ignition switch IG1,
and repair if necessary. If harness wire is okay, replace combination
meter.
Light Does Not Turn Off
1) Before proceeding, see SERVICE PRECAUTIONS. Connect
negative battery cable and turn ignition switch to ON position. If SRS
warning light stays on when C-122 is disconnected, go to next step. If
SRS warning light turns off when C-122 is disconnected, replace SRS-
ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
2) Check connector C-122, and repair if necessary. If
connector is okay, check trouble symptoms. If fault still exists,
check wire harness between SRS-ECU and combination meter, and repair
if necessary.
DTC 44: SRS WARNING LIGHT DRIVE CIRCUIT SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
Before proceeding, see SERVICE PRECAUTIONS. Check SRS warning
light drive circuit system. If warning light drive system is okay,
replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL &
INSTALLATION. Check for DTCs. See SYSTEM OPERATION CHECK.
DTC 45: SRS-ECU EEPROM & A/D CONVERTER SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 51 & 52: DRIVER-SIDE AIR BAG MODULE (SQUIB IGNITION
DRIVE CIRCUIT) SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 54 & 55: PASSENGER-SIDE AIR BAG MODULE (SQUIB
IGNITION DRIVE CIRCUIT) SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
COMPONENT TESTING
CLOCKSPRING TEST
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
system. See DISABLING & ACTIVATING AIR BAG SYSTEM.
2) Remove driver-side air bag module and clockspring. See
DRIVER-SIDE AIR BAG MODULE & CLOCKSPRING under REMOVAL & INSTALLATION.
Check connectors, protective tubing, and case for damage, and
terminals for deformities. Check for continuity between No. 1
connector of clockspring and connectors No. 3 and 4. See Figs. 12 and
13.
3) Align paint mark of SRS Check Harness (MB991613) connector
No. 4 with notch in clockspring connector No. 2 and connect. See
Fig. 14. Check continuity between terminals No. 22 and 23 of SRS check
harness connector No. 5. See Fig. 13.
4) Replace clockspring if any damage was found or continuity
does not exist between specified terminals. See
DRIVER-SIDE AIR BAG MODULE & CLOCKSPRING under REMOVAL & INSTALLATION.
Fig. 11: Identifying Clockspring Connectors
Courtesy of Mitsubishi Motor Sales of America.
Fig. 12: Checking Continuity Between Clockspring Connectors
Courtesy of Mitsubishi Motor Sales of America.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст