Mitsubishi Montero (1998+). Manual — part 43

14

No. 1 Shift Solenoid

In 1st Or 2nd

Battery

14

No. 1 Shift Solenoid

In 3rd Or 4th Gear

0 Volts

15

Power Supply

Ignition ON

Battery

15

Power Supply

Ignition OFF

0 Volts

16

No. 2 Shift Solenoid

In 2nd Or 3rd Gear

Battery

16

No. 2 Shift Solenoid

In 1st Or 4th Gear

0 Volts

17

Diagnostic Test Mode

Not Specified

Not Specified

18

Diagnostic Output

Scan Tool Not

Battery

Connected

21

Oil Temp Warning Lamp

Normal Temp. Range

0 Volts

21

Oil Temp Warning Lamp

For 5 Seconds After

Battery

Ign. Is On

22

Oil Temp Sensor

Temp @ 248

F (120

C)

About 1.9

22

Oil Temp Sensor

Temp @ 302

F (150

C)

About 1.1

23

4WD Low Range Switch

4WD Lever In 4H-Lock

Battery

23

4WD Low Range Switch

4WD Lever In 4L-Lock

0 Volts

24

Neutral Safety Switch

In "R" Position

Battery

24

Neutral Safety Switch

Except In "R"

0 Volts

25

Ground

Engine Idling

0 Volts

26

Ground

Engine Idling

0 Volts

31

Neutral Safety Switch

In "L" Position

Battery

31

Neutral Safety Switch

Except In "L"

0 Volts

32

Neutral Safety Switch

In "N" Position

Battery

32

Neutral Safety Switch

Except In "N"

0 Volts

34

Power Mode

Power Mode Selected

Battery

34

4WD Detection Switch

2WD

4 Volts Or

Montero

Greater

34

4WD Detection Switch

4WD

0-1 Volts

Montero

34

Free Wheel

2WD

4 Volts Or

Montero

Engage Switch

Greater

Sport

34

Free Wheel

4WD

0 Volts

Montero

Engage Switch

Sport

35

Output Speed

Ignition Off

0 Volts

Sensor Gnd

35

Output Speed

Ignition On

2.5 Volts

Sensor Gnd

36

Input Speed Sensor Gnd

Ignition Off

0 Volts

36

Input Speed Sensor Gnd

Ignition On

2.5 Volts

37

Overdrive OFF Signal

(1) Steady Driving @

Battery

31 MPH (50 km/h)

37

Overdrive OFF Signal

(1) Climbing Hill @

0 - 1

31 MPH (50 km/h)

38

Engine Ign. Signal

Engine @ 3000 RPM

.3 - 3.0

39

Neutral Safety Switch

In "D" Position

Battery

39

Neutral Safety Switch

Except In "D"

0 Volts

40

Neutral Safety Switch

In "2" Position

Battery

40

Neutral Safety Switch

Except In "2"

0 Volts

41

HOLD Mode

HOLD Mode Selected

Battery

41

HOLD Mode

HOLD Mode Not Selected

0 Volts

42

Overdrive Switch

Overdrive ON

0 Volts

42

Overdrive Switch

Overdrive OFF

Battery

43

Output Speed Sensor

Vehicle Stopped

About 2.5

43

Output Speed Sensor

Vehicle Moving

Other Than

2.5

44

Input Speed Sensor

Vehicle Stopped

About 2.5

44

Input Speed Sensor

Vehicle Moving

Other Than

2.5

45

Coolant Temp Sensor

Temp @ 86

F (30

C)

2.5

45

Coolant Temp Sensor

Temp @ 158

F (70

C)

0 Volts

46

MIL Signal

Ignition ON

.5

4.5 Volts

(1) - Test circuit with shift lever in "D" position, mode selector

normal and cruise control on.

REMOVAL & INSTALLATION

BRAKELIGHT SWITCH

Removal & Installation

1) Disconnect electrical connector. Remove lock nut, and

unscrew brakelight switch. To install, screw brakelight switch inward

until brakelight plunger contacts brake pedal.

2) Loosen brakelight switch 1/2 to one turn. Install and

tighten lock nut on brakelight switch. Install electrical connector.

Ensure brakelights and cruise control operate properly.

INPUT SPEED SENSOR

Removal & Installation

Disconnect electrical connector. Remove bolt securing sensor

to transmission. Remove input speed sensor from transmission. See

Fig. 14. To install, reverse removal procedure.

Fig. 14: Locating Input Speed Sensor

Courtesy of Mitsubishi Motor Sales of America.

OIL TEMPERATURE SENSOR

Removal & Installation

Sensor is located on transmission connected to cooler line,

near PNP switch. Disconnect electrical connector. Remove oil

temperature sensor from transmission. To install, reverse removal

procedure using NEW gasket.

OUTPUT SPEED SENSOR

Removal & Installation

Disconnect electrical connector from output speed sensor. See

Fig. 15. Remove bolt and output speed sensor. To install, reverse

removal procedure.

Fig. 15: Locating Output Speed Sensor & Connector

Courtesy of Mitsubishi Motor Sales of America.

PARK/NEUTRAL POSITION (PNP) SWITCH

Removal

Switch is located on side of transmission. Remove manual

lever from control shaft on transmission. Bend up tabs on lock washer.

Remove lock nut, lock washer and seal from control shaft. Remove

retaining bolt and neutral safety switch.

Installation

1) Install switch on control shaft. Loosely install switch

retaining bolt. Install seal and lock washer. Install lock nut and

tighten to specification. See TORQUE SPECIFICATIONS.

2) Switch must be adjusted. Ensure parking brake is applied.

Temporarily install manual lever on control shaft. Place shift lever

in Neutral. Remove manual lever. Rotate switch and align reference

mark on switch with groove.

3) Hold switch in this position. Tighten retaining bolt to

specification. Bend tabs on lock washer over against lock nut. To

install remaining components, reverse removal procedure.