Mitsubishi Montero Sport (2004+). Manual — part 690
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-325
STEP 4. Measure the supply voltage at A/T control relay
connector C-97.
(1) Disconnect the A/T control relay and measure at the
harness side.
(2) Measure the voltage between terminal 1 and ground.
• The measured voltage should equal battery positive
voltage.
Q: Is the measured voltage equal to battery positive
voltage?
YES : Go to Step 7.
NO : Go to Step 5.
STEP 5. Check junction block connectors D-09 and D-02
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 6.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC202440
1
3 4
2
CONNECTOR: C-97
AB
C-97
AC100560
1
2
3
4
C-97 HARNESS CONNECTOR:
COMPONENT SIDE
AD
AC202390
JUNCTION BLOCK (FRONT)
1
D-02 (GR)
AB
CONNECTOR: D-02
AC202391
JUNCTION BLOCK (REAR)
7 8
2
3
6
5
1
4
CONNECTOR: D-09
D-09
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-326
STEP 6. Check the harness for open circuit or short circuit
to ground between A/T control relay connector C-97
terminal 1 and fusible link.
Q: Is the harness wire in good condition?
YES : Go to Step 17.
NO : Repair or replace the harness wire.
STEP 7. Measure the resistance at A/T control relay
connector C-97.
(1) Disconnect the A/T control relay and measure at the
harness side.
(2) Measure the resistance between terminal 2 and ground.
• The resistance should measure less than 2 ohms.
Q: Is the measured resistance less than 2 ohms?
YES : Go to Step 9.
NO : Go to Step 8.
STEP 8. Check the harness for open circuit or damage
between A/T control relay connector C-97 terminal 2 and
ground.
Q: Is the harness wire in good condition?
YES : Go to Step 17.
NO : Repair or replace the harness wire.
AC202440
1
3 4
2
CONNECTOR: C-97
AB
C-97
AC202440
1
3 4
2
CONNECTOR: C-97
AB
C-97
AC100561
1
2
3
4
C-97 HARNESS CONNECTOR:
COMPONENT SIDE
AD
AC202440
1
3 4
2
CONNECTOR: C-97
AB
C-97
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-327
STEP 9. Measure the control voltage to A/T control relay
connector C-97.
(1) Disconnect the A/T control relay and measure at the
connector side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 4 and ground.
• The measured voltage should equal battery positive
voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage equal to battery positive
voltage?
YES : Go to Step 14.
NO : Go to Step 10.
AC202440
1
3 4
2
CONNECTOR: C-97
AB
C-97
AC100562
1
2
3
4
C-97 HARNESS CONNECTOR:
COMPONENT SIDE
AD
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-328
STEP 10. Measure the supply voltage at PCM connector
C-90 by backprobing.
(1) Do not disconnect connector C-90.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 50 and ground by
backprobing.
• The measured voltage should equal battery positive
voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage equal to battery positive
voltage?
YES : Go to Step 11.
NO : Go to Step 13.
PCM
60
46
66
57
45
44
64
55 56
65
62 63
52 53
5051
61
42
59
48
41
47
58
43
49
54
AC202313
C-90 (GR)
AB
CONNECTOR: C-90
C-90 (GR)
AC002010 AJ
C-90 HARNESS CONNECTOR:
HARNESS SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст