Mitsubishi Montero Sport (2004+). Manual — part 159
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-49
(1) Disconnect the connector A-01 and measure at the harness
side.
(2) Check for the continuity between terminal No. 5 and
ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 12.
NO : Go to Step 10.
STEP 10. Check connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 13.
AK103913
3
4
5
1
2
6
7
CONNECTOR: A-01
A-01(B)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AKX01409AM
A-01 HARNESS CONNECTOR:
COMPONENT SIDE
7 6 5 4 3 2 1
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-50
STEP 11. Check for open circuit and harness damage
between volume airflow sensor connector A-01 (terminal
No. 5) and PCM connector C-90 (terminal No. 57).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 13.
NO : Repair it. Then go to Step 13.
STEP 12. Check connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Replace the volume airflow sensor. Then go to Step
13.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 13.
STEP 13. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0102 set?
YES : Repeat the troubleshooting.
NO : The procedure is complete.
AK103913
3
4
5
1
2
6
7
CONNECTOR: A-01
A-01(B)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-51
DTC P0106: Manifold Absolute Pressure Circuit Range/Performance Problem
BL
ACK
BL
ACK
2 3
1
GREEN-
YELL
OW
YELL
OW
AK301860
Manifold Absolute Pressure Sensor Circuit
A-12
(MU802723)
1
POWERTRAIN CONTROL MODULE (PCM)
3
2
MANIFOLD ABSOLUTE
PRESSURE SENSOR
12
17
91
57
46
5V
C-90
71
76
77
72 73 74
75
79 80
78
81
87 88
89
91
90
92
97
98
82
93
83
94
84 85
95
86
96
C-91
(MU803782)
47
41
42 43
48 49 50 51 52 53 54 55 56 57
46
45
44
58
59
60 61 62 63
64 65 66
C-90
(MU803781)
1
10
2 3 4 5 6 7 8 9
11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
C-71
C-91
JOINT
CONNEC-
TOR (4)
AK200033AC
CONNECTOR: A-12
MANIFOLD
ABSOLUTE
PRESSURE
SENSOR
A-12(B)
AK103738AE
CONNECTORS: C-90, C-91
PCM
C-91(GR)
C-90(GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-52
.
CIRCUIT OPERATION
• A 5-volt voltage is supplied to the manifold abso-
lute pressure sensor power terminal (terminal No.
3) from the PCM (terminal No. 46). The ground
terminal (terminal No. 2) is grounded with PCM
(terminal No. 57).
• A voltage that is proportional to the intake mani-
fold pressure is sent to the PCM (terminal No. 91)
from the manifold absolute pressure sensor out-
put terminal (terminal No. 1).
.
TECHNICAL DESCRIPTION
• The manifold absolute pressure sensor outputs a
voltage which corresponds to the intake manifold
pressure.
• The PCM checks whether this voltage is within a
specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Compare load value with manifold absolute pressure
sensor output voltage.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Engine coolant temperature sensor
• Throttle position sensor
.
AK103912AB
CONNECTOR: C-71
C-71
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст