Mitsubishi Montero Sport (2004+). Manual — part 637
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-113
DTC 26: Stoplight Switch System
Stoplight Switch System Circuit
AC309388
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-114
.
AC309389
CONNECTOR: C-66
C-66 (B)
AB
1
3 4
2
AC202389
11
4
3
9
8
10
5 6
2
1
7
CONNECTOR: C-85
C-85
AB
AC202317
PCM
120
107
119
106
129 130
118
105
117
114115116
126127128
104
111
103
112
108
101102
109110
121122123
124
113
125
CONNECTOR: C-92
C-92 (GR)
AB
AC202390
JUNCTION BLOCK (FRONT)
1
D-02 (GR)
AB
CONNECTOR: D-02
AC202391
JUNCTION BLOCK (REAR)
7 8
2
3
6
5
1
4
CONNECTOR: D-09
D-09
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-115
CIRCUIT OPERATION
• Battery positive voltage is supplied to the stop-
light switch (terminal 2).
• When the brake pedal is depressed, battery posi-
tive voltage is applied to the PCM (terminal 123).
.
DTC SET CONDITIONS
If the stoplight switch is on for five minutes or more
while driving above 50 km/h (31 mph), or all of the
stop light bulbs are blown, it is judged there is a short
circuit or open circuit in the stoplight switch. This
causes DTC 26 to be set.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Malfunction of the stoplight switch circuit
• Malfunction of stoplight bulb
• Damaged harness, connector
• Malfunction of the PCM
DIAGNOSIS
Required Special Tool:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
STEP 1. Check the brake pedal height.
Refer to GROUP 35A, On-vehicle Service
− Brake Pedal
Check and Adjustment
Q: Is the height adjusted properly?
YES : Go to Step 2.
NO : Adjust the brake pedal to the proper height.
STEP 2. Check the stoplight bulb.
Refer to GROUP 54A, Rear combination light
Q: Is the stoplight bulb in good condition?
YES : Go to Step 3.
NO : Replace the stoplight switch. Refer to GROUP 35A,
Brake Pedal
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-116
STEP 3. Using scan tool MB991958, check data list item 26:
Stoplight Switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to data reading mode.
• Item 26: Stoplight Switch.
• When the brake pedal is depressed, the display on
scan tool MB991958 should be "ON."
• When the brake pedal is not depressed, the display
on scan tool MB991958 should be "OFF."
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the switch operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Go to Step 4.
STEP 4. Measure the stoplight switch power supply
voltage at connectors C-66 by backprobing.
(1) Remove the stoplight switch from the mounting bracket.
(2) Do not disconnect connector C-66.
(3) Measure the voltage between terminal 2 and ground by
backprobing.
• The voltage should measure battery positive voltage.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 7.
NO : Go to step 5.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AC309389
CONNECTOR: C-66
C-66 (B)
AB
1
3 4
2
AC203804
1
2
2
4
1
3
AC
C-66 HARNESS
CONNECTOR:
HARNESS SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст