Mitsubishi Montero Sport (2004+). Manual — part 715
A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-425
STEP 3. Check the lock cam.
Q: Is the lock cam in good condition?
YES :
Go to Step 4.
NO :
Replace the lock cam. Refer to
.
Check that the ignition key can not be
turned to the "LOCK" (OFF) position with
the selector lever at any position other than
"P" position.
STEP 4. Check the fit of the key interlock cable.
Q: Is the key interlock cable installed correctly?
YES :
Go to Step 5.
NO :
Install the key interlock cable correctly.
Refer to
. Check that the ignition
key can not be turned to the "LOCK" (OFF)
position with the selector lever at any
position other than "P" position.
STEP 5. Check the key interlock cable.
Q: Is the key interlock cable in good condition?
YES :
Go to Step 6.
NO :
Replace the key interlock cable. Refer to
. Check that the ignition key can
not be turned to the "LOCK" (OFF) position
with the selector lever at any position other
than "P" position.
STEP 6. Check the fit of the transmission control
cable.
Q: Is the transmission control cable installed
correctly?
YES :
Replace the steering lock cylinder
assembly. Refer to
and
Check that the ignition key can not be
turned to the "LOCK" (OFF) position with
the selector lever at any position other than
"P" position.
NO :
Install the transmission control cable
correctly. Refer to
. Check that
the ignition key can not be turned to the
"LOCK" (OFF) position with the selector
lever at any position other than "P" position.
SPECIAL TOOLS
TSB Revision
AUTOMATIC TRANSMISSION
23A-426
SPECIAL TOOLS
M1231100600164
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
MUT-III sub assembly
A: Vehicle
communication
interface (V.C.I.)
B: MUT-III USB cable
C: MUT-III main
harness A (Vehicles
with CAN
communication
system)
D: MUT-III main
harness B (Vehicles
without CAN
communication
system)
E: MUT-III main
harness C (for
Daimler Chrysler
models only)
F: MUT-III
measurement
adapter
G: MUT-III trigger
harness
MB991824-KIT
NOTE: G:
MB991826 MUT-III
trigger harness is
not necessary
when pushing
V.C.I ENTER key
Checking diagnostic trouble
codes
MD998330 (Includes
MD998331)
Oil pressure gauge
(3.0 MPa, 427 psi)
MD998330-01
Measurement of hydraulic
pressure
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
A
B
C
D
E
F
G
DO NOT USE
AC103525
ON-VEHICLE SERVICE
TSB Revision
AUTOMATIC TRANSMISSION
23A-427
ON-VEHICLE SERVICE
AUTOMATIC TRANSMISSION CONTROL COMPONENT LAYOUT
M1231102000157
MD998332
Adapter
MD998332-01
Connection for oil pressure
gauge
MD998900
Adapter
MD998900-01
Connection for oil pressure
gauge
MB995062
Flushing tool
−
Flushing cooler and tube
MD998727 Oil pan
remover
MD998727-01
Removal of oil pan
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
D998727
NAME
SYMBOL NAME
SYMBOL
A/T control relay
K
Output shaft speed sensor
H
A/T control solenoid valves
I
Transmission range switch
E
Transmission fluid temperature sensor
J
Powertrain control module (PCM)
L
Crankshaft position sensor
C
Stoplight switch
M
Data link connector (1), (2)
N
TP sensor
A
Dual pressure switch
B
Transfer low detection switch <V4A51>
G
Input shaft speed sensor
D
Vehicle speed sensor
F
ON-VEHICLE SERVICE
TSB Revision
AUTOMATIC TRANSMISSION
23A-428
AC101193
A
B
C
D
E
F
G
H
I
J
K
L
M
N
AB
AC002593
TP SENSOR
AH
A
AC002641
B
DUAL PRESSURE
SWITCH
AC
AC002599
CRANKSHAFT
POSITION SENSOR
AC
C
AC002609
D
AC
INPUT SHAFT
SPEED SENSOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст