Mitsubishi Montero Sport (2004+). Manual — part 704
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-381
STEP 7. Using scan tool MB991958, check data list item 65:
Dual Pressure Switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to data reading mode.
• Item65: Dual Pressure Switch.
• When the A/C is in operation, the scan tool
MB991958 display should be "ON."
• When the A/C is not in operation, the scan tool
MB991958 display should be "OFF."
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the switch operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
.
NO : Check the air conditioning system. Refer to GROUP
55, Troubleshooting Strategy
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-382
STEP 8. Check automatic compressor controller connector
C-09 and intermediate connector C-41 for loose, corroded
or damaged terminals, or terminals pushed back in the
connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
STEP 9. Check the harness for open circuit between dual
pressure switch connector A-23 terminal 1 and automatic
compressor controller connector C-09 terminal 2.
Q: Is the harness wire in good condition?
YES : Go to Step 15.
NO : Repair or replace the harness wire.
AC103771
CONNECTOR: C-09
AF
C-09
4
2
1
3
AC202442
22
2021
10
9
8
1718
6 7
19
1415
4 5
1112
1 2 3
13
16
CONNECTOR: C-41
C-41
AB
AC202889
1 2
AB
CONNECTOR: A-23
A-23 (BR)
AC103771
CONNECTOR: C-09
AF
C-09
4
2
1
3
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-383
STEP 10. Measure the switch output voltage at PCM
connector C-91 by backprobing.
(1) Do not disconnect connector C-91.
(2) Start the engine and run at idle.
(3) Operate the A/C.
(4) Measure the voltage between terminal 83 and ground by
backprobing.
• When the A/C is in operation, the voltage should mea-
sure battery positive voltage.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 16.
NO : Go to Step 11.
AC202435
PCM
59
68
58
67
46 47
57
56
53
64
54
65
55
66
50
62
51
63
49
48
60 61
52
44
41 42 43
45
AC202435
PCM
CONNECTOR: C-91
AB
C-91 (GR)
71 72 73 74
75 76
77
78 79 80 81 82 83 84 85 86 87 88
90 91
92 93 94
95 96
97
98
89
AC002096 AJ
C-91 HARNESS CONNECTOR:
HARNESS SIDE
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-384
STEP 11. Check A/C refrigerant temperature switch
connector A-25, intermediate connector A-89 and PCM
connector C-91 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 12.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC202894
6
3
4
1 2
5
2
1
3
CONNECTORS: A-25, A-89
A-25 (B)
A-89 (B)
AB
AC202435
PCM
59
68
58
67
46 47
57
56
53
64
54
65
55
66
50
62
51
63
49
48
60 61
52
44
41 42 43
45
AC202435
PCM
CONNECTOR: C-91
AB
C-91 (GR)
71 72 73 74
75 76
77
78 79 80 81 82 83 84 85 86 87 88
90 91
92 93 94
95 96
97
98
89
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст