Mitsubishi Montero Sport (2004+). Manual — part 641
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-129
STEP 4. Check harness for open circuit or short circuit to
ground between transmission range switch connector
B-01 terminal 7 and junction block connector D-13 terminal
11.
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair or replace the harness wire.
AC202393
4
9
5
10
3
8
2
7
6
1
CONNECTOR: B-01
<RWD>
<4WD>
B-01 (B)
B-01 (B)
AB
AC202368
JUNCTION BLOCK
(REAR)
19 20
6
17
7
5
15
14
16
8
18
3
11 12
4
2
10
1
9
13
CONNECTOR: D-13
D-13
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-130
STEP 5. Using scan tool MB991958, check data list item 61:
Transmission Range Switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to data reading mode.
• Item 61: Transmission Range Switch.
• Move the selector lever to the "P," "R," "N," "D," "3,"
"2," "L" positions and confirm that the selected trans-
mission ranges match the positions shown on scan
tool MB991958.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the switch operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
.
NO : Replace the PCM.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-131
STEP 6. Check the transmission range switch.
Measure the resistance between the terminals for each trans-
mission range as indicated in the table below.
Q: Is the measured resistance less than 2 ohms for each
selector position?
YES : Go to Step 7.
NO : Replace the transmission range switch. Refer to
GROUP 23B, Transmission
TRANSMISSION
RANGE
TERMINAL
CONNECTION OF
TESTER
SPECIFIED
CONDITION
P
1
− 7
Less than 2 ohms.
R
7
− 8
N
2
− 7
D
3
− 7
3
4
− 7
2
5
− 7
L
6
− 7
AC202393
4
9
5
10
3
8
2
7
6
1
CONNECTOR: B-01
<RWD>
<4WD>
B-01 (B)
B-01 (B)
AB
AC004076
P
R
N
D
3
2
L
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-132
STEP 7. Check transmission range switch connector B-01
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC202393
4
9
5
10
3
8
2
7
6
1
CONNECTOR: B-01
<RWD>
<4WD>
B-01 (B)
B-01 (B)
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст