Mitsubishi Montero Sport (2004+). Manual — part 564
RADIO AND TAPE PLAYER
TSB Revision
CHASSIS ELECTRICAL
54-243
STEP 9. Check antenna motor-ECU connector C-34 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is antenna motor-ECU connector C-34 in good
condition?
YES : Go to Step 10.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
.
STEP 10. Check the harness wires between antenna
motor-ECU connector C-34 (terminal No. 6) and radio and
CD player connector C-62 (terminal No.3).
Q: Are the harness wires between antenna motor-ECU
connector C-34 (terminal No. 6) and radio and CD player
connector C-62 (terminal No.3) in good condition?
YES : Go to Step 11.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
.
AC201808
1
5
2
6
7
3
8
4
9
CONNECTOR : C-34
COMPONENT SIDE
AB
C-34
AC201808
1
5
2
6
7
3
8
4
9
CONNECTOR : C-34
COMPONENT SIDE
AB
C-34
AC200783
1
7
2
8
10
11
5
13
6
14
12
4
9
3
CONNECTOR: C-62
COMPONENT SIDE
AB
C-62
RADIO AND TAPE PLAYER
TSB Revision
CHASSIS ELECTRICAL
54-244
STEP 11. Measure the voltage at the antenna motor-ECU
power supply circuit. (Fusible link number 8)
(1) Disconnect antenna motor-ECU connector C-34 and
measure at harness side.
(2) Measure the voltage between terminal number 2 and
ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Does the measured voltage correspond with this range?
YES : Go to Step 13.
NO : Go to Step 12.
STEP 12. Check the harness wires between fusible link
number 8 and antenna motor-ECU connector C-34
(terminal No.1 and 2).
AC201808
1
5
2
6
7
3
8
4
9
CONNECTOR : C-34
COMPONENT SIDE
AB
C-34
1
5
2
6
7
3
8
4
9
AC202641
C-34
HARNESS CONNECTOR:
COMPONENT SIDE
AB
AC201808
1
5
2
6
7
3
8
4
9
CONNECTOR : C-34
COMPONENT SIDE
AB
C-34
RADIO AND TAPE PLAYER
TSB Revision
CHASSIS ELECTRICAL
54-245
NOTE: After inspecting junction block connectors D-01, D-06
and IOD or storage connector A-54X, inspect the wire. If junc-
tion block connectors D-01, D-06 and IOD or storage connector
A-54X are damaged, repair or replace them. Refer to GROUP
00E, Harness Connector Inspection
Q: Are the harness wires between fusible link number 6
and antenna motor-ECU connector C-34 in good
condition?
YES : Go to Step 13.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
.
AC200774
2
1
CONNECTOR: A-54X
AB
A-54X
AC309275AB
CONNECTOR: D-01, D-06
D-01
D-06
JUNCTION BLOCK (FRONT)
D-01
D-06
RADIO AND TAPE PLAYER
TSB Revision
CHASSIS ELECTRICAL
54-246
STEP 13. Measure the voltage at the antenna motor-ECU
power supply circuit. (Ignition switch "ACC")
(1) Disconnect antenna motor-ECU connector C-34 and
measure at harness side.
(2) Turn the ignition switch to the "ACC" position.
(3) Measure the voltage between terminal number 9 and
ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Does the measured voltage correspond with this range?
YES : Go to Step 15.
NO : Go to Step 14.
STEP 14. Check the harness wires between ignition switch
"ACC" and antenna motor-ECU connector C-34 (terminal
No. 9).
AC201808
1
5
2
6
7
3
8
4
9
CONNECTOR : C-34
COMPONENT SIDE
AB
C-34
1
5
2
6
7
3
8
4
9
AC202646
C-34
HARNESS CONNECTOR:
COMPONENT SIDE
AB
4
9
3
8
7
2
6
1
5
22
2021
10
9
8
1718
6 7
19
1415
4 5
1112
1 2 3
13
16
AC201810
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст