Mitsubishi Montero Sport (2004+). Manual — part 315
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-673
DTC P0554: Power Steering Pressure Sensor Circuit Intermittent
.
CIRCUIT OPERATION
• A battery positive voltage is applied to the power
steering pressure switch output terminal (terminal
No. 1) from the PCM (terminal No. 52) via the
resistor in the PCM.
.
TECHNICAL DESCRIPTION
• The power steering pressure switch converts the
existence of a power steering load into a high/low
voltage, and inputs it into the PCM.
• When the steering wheel is turned, hydraulic
pressure rises. The power steering pressure
switch closes, and the applied battery positive
voltage will be grounded. With this, the power
steering pressure switch output voltage will fluc-
tuate between 12 volts and 0 volt.
• While driving with the steering wheel held
straight, the power steering pressure switch turns
"OFF".
• The PCM checks whether the power steering
pressure switch turns "OFF" or "ON" during driv-
ing.
.
DESCRIPTIONS OF MONITOR METHODS
Power steering pressure switch stays on during
specified go/stop operations.
.
MONITOR EXECUTION
Continuous
.
AK000604
Power Steering Pressure Switch Circuit
BL
UE-
WHITE
52
1
POWER STEERING
PRESSURE SWITCH
POWERTRAIN CONTROL
MODULE (PCM)
1
A-76
47
41
42 43
48 49 50 51 52 53 54 55 56 57
46
45
44
58
59
60 61 62 63
64 65 66
C-90
(MU803781)
AK200032 AB
CONNECTOR: A-76
POWER STEERING
PRESSURE SWITCH
A-76
AK103738AC
CONNECTOR: C-90
PCM
C-90(GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-674
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Engine coolant temperature sensor
.
LOGIC FLOW CHART
.
Check Conditions
• Engine coolant temperature is higher than 30°C
(86
°F).
• Vehicle speed is higher than 50 km/h (31 mph).
Judgment Criteria
• The ON/OFF frequency of a power steering pres-
sure switch is 10 Hz or more for 20 seconds.
.
OBD-II DRIVE CYCLE PATTERN
None.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are: )
• Power steering pressure switch failed.
• Air entered to power steering system.
• Open or shorted power steering pressure switch
circuit, harness damage or connector damage.
• PCM failed.
START
END
NO
NO
YES
YES
YES
NO
MALFUNCTION
GOOD
CONTINUOUS FAILURE
FOR 20secs
FREQUENCY > 10Hz
MONITORING
CONDITIONS
AK301790
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-675
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I
• MB991827: USB Cable
• MB991911: Main Harness B
STEP 1. Using scan tool MB991958, check data list item 27:
Power Steering Pressure Switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
27, Power Steering Pressure Switch.
• If the steering wheel is stopped while idling, "OFF" will
be displayed.
• If the steering wheel is steered while idling, "ON" will be
displayed.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Go to Step 2.
STEP 2. Check the power steering fluid level.
Refer to GROUP 37A, On-Vehicle Service - Fluid Level Check
.
Q: Are there any abnormalities?
YES : Go to Step 3.
NO : Repair it. Then go to Step 7.
STEP 3. Check the power steering pressure switch.
Refer to GROUP 37A, On-Vehicle Service - Power Steering
Pressure Switch Check
Q: Are there any abnormalities?
YES : Go to Step 4.
NO : Replace the power steering pressure switch. Then go
to Step 7.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-676
STEP 4. Check the oil pump pressure .
Refer to GROUP 37A, On-Vehicle Service - Oil Pump Pressure
Test
Q: Are there any abnormalities?
YES : Go to Step 5.
NO : Repair it. Then go to Step 7.
STEP 5. Check connector A-76 at the power steering
pressure switch and connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 6.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 7.
AK200031
1
AB
CONNECTOR: A-76
A-76
HARNESS CONNECTOR:
COMPONENT SIDE
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст