Mitsubishi Montero Sport (2004+). Manual — part 549
RADIO AND TAPE PLAYER
TSB Revision
CHASSIS ELECTRICAL
54-183
.
CIRCUIT OPERATION
Power is supplied to the radio and CD player when
the ignition switch is at the "ACC" or "ON" position.
.
TECHNICAL DESCRIPTION (COMMENT)
The cause is probably a faulty radio and CD player
power supply circuit system.
.
TROUBLESHOOTING HINTS
• Damaged harness wire or connector
• Malfunction of the radio and CD player
.
AC003431
CONNECTOR: A-54X
A-54X
AC
AC003488
CONNECTORS: C-41, C-62
C-41
C-62
AB
AC003461AC
CONNECTOR: D-06
JUNCTION BLOCK (FRONT)
D-06
AC003457AE
CONNECTOR: D-08
JUNCTION BLOCK (REAR)
D-08
RADIO AND TAPE PLAYER
TSB Revision
CHASSIS ELECTRICAL
54-184
DIAGNOSIS
Required Special Tool:
• MB991223: Harness set
STEP 1. Check the radio and CD player power supply
circuit by backprobing.
(1) Do not disconnect radio and CD player connector C-62.
(2) Turn the ignition switch to the "ACC" position.
(3) Measure the voltage between terminal 10 and ground by
backprobing.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Does the measured voltage correspond with this range?
YES : Go to Step 4.
NO : Go to Step 2.
STEP 2. Check radio and CD player connector C-62 for
damage.
Q: Is radio and CD player connector C-62 in good
condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. If the power switch is
turned on, the radio and CD player should operate
normally.
AC200783
1
7
2
8
10
11
5
13
6
14
12
4
9
3
CONNECTOR: C-62
COMPONENT SIDE
AB
C-62
AC002810 AB
CONNECTOR C-62
(HARNESS SIDE)
AC200783
1
7
2
8
10
11
5
13
6
14
12
4
9
3
CONNECTOR: C-62
COMPONENT SIDE
AB
C-62
RADIO AND TAPE PLAYER
TSB Revision
CHASSIS ELECTRICAL
54-185
STEP 3. Check the harness wires between radio and CD
player connector C-62 (terminal No.10) and ignition switch
(ACC).
AC003488
22
2021
10
9
8
1718
6 7
19
1415
4 5
1112
1 2 3
13
16
1
7
3 2
8
10
4
1211
5
13
6
14
9
CONNECTORS: C-41, C-62
C-41
C-62
AB
C-62
HARNESS SIDE
C-41
RADIO AND TAPE PLAYER
TSB Revision
CHASSIS ELECTRICAL
54-186
NOTE: After inspecting intermediate connector C-41, IOD or
storage connector A-54X and junction block connectors D-06
and D-08, inspect the wire. If intermediate connector C-41, IOD
or storage connector A-54X and junction block connectors
D-06 and D-08 are damaged, repair or replace them. Refer to
GROUP 00E, Harness Connector Inspection
Q: Are the harness wires between radio and CD player
connector C-62 (terminal No.10) and ignition switch
(ACC) in good condition?
YES : There is no action to be taken.
NO : Repair them. If the power switch is turned on, the
radio and CD player should operate normally.
STEP 4. Check that the radio and CD player are installed
correctly.
NOTE: The radio and CD player are grounded to the instru-
ment panel center reinforcement directly.
Q: Are the radio and CD player installed correctly?
YES : Go to Step 5.
NO : Install properly. If the power switch is turned on, the
radio and CD player should operate normally.
STEP 5. Recheck for malfunction.
Q: Is a malfunction eliminated?
YES : The procedure is complete. (If no malfunctions are
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Point
− How to
Cope with Intermittent Malfunction
.)
NO : Go to Step 1.
AC200772
1
8
3
4
5
7 6
10
15
16
14
12
13
11
9
2
COMPONENT SIDE
CONNECTOR: D-06
D-06
JUNCTION BLOCK
(FRONT)
AB
AC200773
M
3
1
4
2
CONNECTOR: D-08
D-08
COMPONENT SIDE
AB
AC200774
2
1
CONNECTOR: A-54X
AB
A-54X
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст