Mitsubishi Montero Sport (2004+). Manual — part 727
GRILL, MOLDING AND GARNISH
TSB Revision
EXTERIOR
51-7
AC203217
E
6
5
B
A
B
C
D
E
B
B
ADHESIVE TAPE:
DOUBLE-SIDED TAPE <A, C, E [ 1.2 mm ( 0.05 in ) THICKNESS ],
C [ 5 mm ( 0.2 in ) WIDTH AND 1.2 mm ( 0.05 in ) THICKNESS ],
D [ 12 mm ( 0.5 in ) WIDTH AND 1.2 mm ( 0.05 in ) THICKNESS ]>
4.9 N·m
43 in-lb
10
NOTE
: Clip position
: Claw position
5
6
28 mm
(1.1 in)
62 mm
(2.4 in)
16 mm
(0.63 in)
32.5 mm
(1.28 in)
15 mm
(0.6 in)
62 mm
(2.4 in)
15 mm
(0.6 in)
15 mm
(0.6 in)
62 mm
(2.4 in)
44 mm
(1.7 in)
15.5 mm
(0.61 in)
7
9
7.5 N·m
65 in-lb
8
AB
<<C>>
>>A<<
5.
FRONT DOOR MOLDING
<<C>>
>>A<<
6.
REAR DOOR MOLDING
REAR DECK GARNISH REMOVAL
STEPS
7. LICENSE PLATE LIGHT
8. REAR WIPER ARM AND BLADE
ASSEMBLY (REFER TO
.)
• LIFTGATE LOWER TRIM
10. LIFTGATE GARNISH
REAR DECK GARNISH REMOVAL
STEPS (Continued)
GRILL, MOLDING AND GARNISH
TSB Revision
EXTERIOR
51-8
REMOVAL SERVICE POINT
.
<<A>>RADIATOR GRLL REMOVAL
Remove the radiator grill by pushing all tabs of the radiator grill
clips in the direction of the arrows with a flat-tipped screwdriver,
then lightly pull the radiator grill toward you.
.
<<B>>ROOF DRIP MOLDING REMOVAL
CAUTION
If the molding has become warped, it should not be
reused.
Use special tool MB990449 to lever out the molding.
.
<<C>> DOOR MOLDING REMOVAL
Gently lift and remove the door molding. If there is any dou-
ble-sided tape remaining on the door molding, remove accord-
ing to the following instructions.
<Remove double-sided tape remaining on the body sur-
face>
1. Attach protection tape all the way along the edges of the
double-sided tape which is still adhering to the body.
2. Scrape off the double-sided tape with a resin spatula as
possible.
3. Peel off the protection tape.
4. Use a shop towel moistened with 3M
AAD Part number
8906 or equivalent to wipe the body.
.
<Remove double-sided tape remaining on double-sided
tape (when re-using door molding)>
AC003753
AC003626AB
MB990449
AC000420
DOUBLE-SIDED TAPE
PROTECTION TAPE
AB
AC000421
DOUBLE-SIDED TAPE
AB
GRILL, MOLDING AND GARNISH
TSB Revision
EXTERIOR
51-9
1. Scrape off the double-sided tape on the door molding with a
resin spatula as possible.
2. Use a shop towel moistened with 3M
AAD Part number
8906 or equivalent to wipe the door molding surface.
3. Remove only a small portion of the residual adhesive.
4. Adhere the double-sided tape as specified on the door
molding. (Refer to double-sided tape adherence location.)
INSTALLATION SERVICE POINTS
.
>>A<<DOOR MOLDING INSTALLATION.
1. Tear off the double-sided tape backing paper.
NOTE: If you attach the adhesive tape to the edge of the
backing paper, it will be easy to tear off.
2. Install the door molding.
NOTE: If the double-sided tape is difficult to affix in cold
temperature, etc., warm the bonding surfaces of the body
and door molding to about 40
−
60
°
C (104
−
140
°
F) before
affixing the tape.
3. Firmly press in the door molding.
AC000422
AC003628
AC000423 AB
ADHESIVE TAPE
BACKING PAPER
WIDE FENDER
TSB Revision
EXTERIOR
51-10
WIDE FENDER
REMOVAL AND INSTALLATION
M1511018200033
Pre-removal and Post-installation Operation
• Mud Guard Removal and Installation
AC003754
1
1
3
2
N
N
AC
NOTE
: Resin clip position
REMOVAL STEPS
<<A>> >>A<<
1. RIVET
2. FRONT FLARE
3. REAR FLARE
REMOVAL STEPS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст