Mitsubishi Montero Sport (2004+). Manual — part 568
ANTENNA
TSB Revision
CHASSIS ELECTRICAL
54-259
REMOVAL SERVICE POINT
.
<<A>> MAST ANTENNA OR MOTOR ANTENNA ASSEMBLY
REMOVAL
To make installation easy, tie a string on the feeder cable of the
mast antenna or motor antenna assembly and pull.
INSPECTION
M1543019501608
MOTOR ANTENNA CHECK
Disconnect the antenna motor-ECU connector. Check that the
antenna extends when the positive terminal of the battery is
connected to terminal number 1 and the negative terminal of
the battery is connected to terminal number 2. Check that the
antenna retracts when the connection is reversed.
ANTENNA MOTOR-ECU CHECK
1. Remove the antenna motor-ECU mounting bolts.
2. Operate the radio switch when the ignition switch is turned
to the "ACC" or "ON" position. Measure the voltage between
the terminals while the antenna is attempting to extend or
retract.
AC002829
STRING
AB
AC002830 AB
ANTENNA
OPERATION
DIRECTION
TERMINAL NO.
TO BE
CONNECTED
TO BATTERY
SPECIFIED
CONDITION
While lowering
1
− 3
10
− 13 volts
While rising
4
− 3
10
− 13 volts
AC002813
AC
ANTENNA
RETRACT
ANTENNA
EXTEND
ANTENNA
TSB Revision
CHASSIS ELECTRICAL
54-260
GLASS ANTENNA CHECK
1. Wrap an aluminum foil around the tester probe a shown.
CAUTION
Be careful not to damage the print wire.
2. Check continuity while pressing the aluminum foil along the
antenna print wire.
ANTENNA POLE REPLACEMENT
M1544000900170
1. Remove the ring nut.
2. After setting the ignition switch to the "ACC" or "ON," turn
the radio switch on. Extend the antenna pole and remove it
together with the rack cable.
3. Pull the antenna out the farthest end.
NOTE: If the motor end side of the rack cable is bent,
straighten it out.
4. Face the teeth side of the rack cable toward the engine
compartment, and feed the rack cable into the motor
assembly.
ACX01954 AB
TESTER PROBE
ALUMINUM FOIL
PRINT WIRE
ACX01953 AB
RING NUT
ANTENNA POLE
ACX01949 AB
RACK CABLE
ANTENNA POLE
ACX01950
RACK CABLE
RACK CABLE
TEETH
ENGINE
COMPARTMENT
SIDE
AB
REAR WINDOW DEFOGGER
TSB Revision
CHASSIS ELECTRICAL
54-261
5. Turn the teeth side of the rack cable toward the front of the
vehicle (90 degree angle to the right), and engage the rack
cable with the motor gears.
6. Pull lightly on the rack cable. If there is no resistance and it
comes out, it is not engaged with the motor gears. Check
that the end of the rack gear is not bent again, and then
repeat steps (3) and (4) above again.
7. Set up the antenna pole vertically, and turn the radio off to
wind in the rack cable. The antenna pole will be pulled into
the motor antenna as the rack cable is wound in.
8. After tightening the ring nut, turn the radio on and off and
check the operation of the antenna pole.
REAR WINDOW DEFOGGER
ON-VEHICLE SERVICE
PRINTED-HEATER LINES CHECK
M1543001800203
1. Run engine at 2,000 r/min. Check heater element with
battery at full.
2. Turn "ON" rear window defogger switch. Measure heater
element voltage with circuit tester at rear window glass
centre A. Condition is good if it indicates about 6 V.
3. If 12 V is indicated at A, there is a break in the negative
terminals from A. Move test bar slowly to negative terminal
to detect where voltage changes suddenly (0V).
4. If 0 V is indicated at A, there is a break in the positive
terminals from A. Defect where the voltage changes
suddenly (12 V) in the same method described above.
ACX01952 AC
RACK CABLE
VEHICLE FRONT
DIRECTION
ACX01951AB
RING NUT
ACX00813
NORMAL CHARACTERISTIC CURVE
ABNORMAL CHARACTERISTIC CURVE
VOLTAGE
A (CENTER POINT)
APPROXIMATELY
6 V
NEGATIVE
TERMINAL
PRINTED
HEATER
LINE
POSITIVE
TERMINAL
NEGATIVE
TERMINAL
PRINTED
HEATER
LINE
POSITIVE
TERMINAL
OPENCIRCUIT
POINT
VOLTAGE
AC
REAR WINDOW DEFOGGER
TSB Revision
CHASSIS ELECTRICAL
54-262
REAR WINDOW DEFOGGER SWITCH
REMOVAL AND INSTALLATION
M1543006200206
INSPECTION
M1543019502690
REAR WINDOW DEFOGGER SWITCH
CONTINUITY CHECK
AC002833
: Metal clip position
NOTE
1
2
3
AB
REMOVAL STEPS
1.
METER BEZEL ASSEMBLY
2.
SWITCH HOLDER
3.
REAR WINDOW DEFOGGER SWITCH
REMOVAL STEPS (Continued)
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
At the "OFF"
position
3 - 4
Open circuit
At the "ON"
position
3 - 4
Less than 2 ohms
AC002834
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст