Mitsubishi Montero Sport (2004+). Manual — part 754
AIR BAG MODULES AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-85
<Air bag module (driver's side), clock spring>
AC003312
1
5
3
39 N·m
29 ft-lb
2
4
AB
AIR BAG MODULE REMOVAL
STEPS
<<A>>
1.
NEGATIVE (
−) BATTERY CABLE
CONNECTION
<<B>>
2.
AIR BAG MODULE
CLOCK SPRING REMOVAL
STEPS
<<A>>
1.
NEGATIVE (
−) BATTERY CABLE
CONNECTION
<<B>>
2.
AIR BAG MODULE
<<C>>
3.
STEERING WHEEL
4.
COLUMN COVER LOWER
<<D>>
5.
CLOCK SPRING
AIR BAG MODULE
INSTALLATION STEPS
>>A<<
•
PRE-INSTALLATION
INSPECTION
>>D<<
2.
AIR BAG MODULE
1.
NEGATIVE (
−) BATTERY CABLE
CONNECTION
>>E<<
•
POST-INSTALLATION
INSPECTION
CLOCK SPRING
INSTALLATION STEPS
>>A<<
•
PRE-INSTALLATION
INSPECTION
>>B<<
5.
CLOCK SPRING
4.
COLUMN COVER LOWER
>>C<<
3.
STEERING WHEEL
>>D<<
2.
AIR BAG MODULE
1.
NEGATIVE (
−) BATTERY CABLE
CONNECTION
>>E<<
•
POST-INSTALLATION
INSPECTION
AIR BAG MODULE
INSTALLATION STEPS
AIR BAG MODULES AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-86
<Air bag module (front passenger's side)>
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
• MB990803: Steering Wheel Puller
• MB991613: SRS Check Harness
AC003313AB
1
3
2
AIR BAG MODULE REMOVAL
STEPS
<<A>>
1.
NEGATIVE (
−) BATTERY CABLE
CONNECTION
2.
STOPPER
<<E>>
3.
AIR BAG MODULE
AIR BAG MODULE
INSTALLATION STEPS
>>A<<
•
PRE-INSTALLATION INSPECTION
3.
AIR BAG MODULE
2.
STOPPER
1.
NEGATIVE (
−) BATTERY CABLE
CONNECTION
>>E<<
•
POST-INSTALLATION
INSPECTION
AIR BAG MODULES AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-87
REMOVAL SERVICE POINTS
.
<<A>> NEGATIVE (
−) BATTERY CABLE DISCONNECTION
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work. (Refer to
.)
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
Disconnect the negative (
−) battery cable from the battery and
tape the terminal to prevent accidental connection and air bags
deployment.
.
<<B>> AIR BAG MODULE REMOVAL (DRIVER'S SIDE)
1. Remove the air bag module mounting screws (TORX
screws) at the sides of the steering wheel.
NOTE: Do not remove the screws from the holders.
CAUTION
When disconnecting the air bag module-to-clock spring
connector, take care not to apply excessive force to it.
WARNING
The removed air bag module should be stored in a
clean, dry place with the pad cover face up.
2. When disconnecting the connector of the clock spring from
the air bag module, press the air bag's lock toward the outer
side to spread it open. Use a flat-tipped screwdriver, as
shown in the figure at the left, to pry gently to remove the
connector.
.
<<C>> STEERING WHEEL REMOVAL
CAUTION
Do not hammer on the steering wheel. Doing so may dam-
age the collapsible column mechanism.
.
ACX00583
INSULATING TAPE
BATTERY
BATTERY CABLE (–)
AC
AC003314
SECTION A - A
A
A
MOUNTING SCREW
(TORX® SCREW)
AB
AC000396AB
FLAT-TIPPED
SCREWDRIVER
LOCK
CLOCK
SPRING-TO-AIR
BAG MODULE
CONNECTOR
LOCK
AC003315AB
MB990803
AIR BAG MODULES AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-88
<<D>> CLOCK SPRING REMOVAL
WARNING
The removed clock spring should be stored in a
clean, dry place.
.
<<E>> AIR BAG MODULE REMOVAL (FRONT
PASSENGER'S SIDE)
WARNING
The removed air bag module should be stored in a
clean, dry place with the ad cover face up.
INSTALLATION SERVICE POINTS
.
>>A<< PRE-INSTALLATION INSPECTION
WARNING
Dispose of air bag modules only according to the
specified procedure. (Refer to
.)
1. When installing the new air bag modules and clock spring,
refer to "INSPECTION" (
2. Connect the negative (
−) battery cable.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
3. Connect scan tool MB991958 to the data link connector.
4. Turn the ignition key to the "ON" position.
5. Conduct diagnostic test using scan tool MB991958 to
ensure entire SRS operates properly.
WARNING
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work. (Refer to
.)
6. Turn the ignition key to the "OFF" position. Disconnect the
negative (
−) battery cable and tape the terminal to prevent
accidental connection and air bags deployment.
.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст