Mitsubishi Montero Sport (2004+). Manual — part 676
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-269
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
Check Conditions
• Solenoid status: either solid ON or OFF.
• Shift status: in-gear.
• Voltage of battery: 10 volts or more.
Judgement Criteria
• Solenoid voltage: 3 volts or less. (0.3 second)
• If DTC 34 (P0768) is set consecutively four times,
the transmission is locked into 3rd gear as a
fail-safe measure, and the "N" range light flashes
once per second.
.
OBD-II DRIVE CYCLE PATTERN
Start the engine, and keep the vehicle stopped in P
range for 5 seconds.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Malfunction of overdrive solenoid valve
• Damaged harness, connector
• Malfunction of the PCM
AC205284
Good
Malfunction
END
START
In-gear?
Shift solenoid-D is in ON
or OFF steady state
Voltage of battery > 10 V
Solenoid circuit
voltage < 3 V
Continuous failure
for 0.3 sec.
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Overdrive solenoid valve is in
ON or OFF steady state
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-270
DIAGNOSIS
Required Special Tool:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
STEP 1. Using scan tool MB991958, check actuator test
item 04: Overdrive Solenoid Valve.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to actuator test mode.
• Item 04: Overdrive Solenoid Valve.
• An audible clicking or buzzing should be heard when
the overdrive solenoid valve is energized.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the solenoid valve operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-271
STEP 2. Using scan tool MB991958, read the A/T
diagnostic trouble code.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC 54 set? (DTC 54 may be set along with multiple
DTCs).
YES : Refer to
DTC 54: A/T Control Relay
System.
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, read the A/T
diagnostic trouble code.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are DTC 32 and DTC 33 set? (Multiple DTCs may be set).
YES : Go to Step 8.
NO : Go to Step 4.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-272
STEP 4. Measure the overdrive solenoid valve resistance
at A/T control solenoid valve assembly connector B-02.
(1) Disconnect connector B-02 and measure at the solenoid
valve side.
(2) Measure the resistance between solenoid valve assembly
connector B-02 terminals 5 and 9.
Resistance value: 2.7
− 3.4 Ω [at 20°C (68°F)]
Q: Is the measured resistance 2.7
− 3.4 Ω [at 20°C (68°F)]?
YES : Go to Step 6.
NO : Go to Step 5.
STEP 5. Measure the solenoid valve resistance at the
overdrive solenoid valve connector B-02-3 inside the
transmission.
(1) Disconnect solenoid valve connector B-02-3 and measure
at the solenoid valve side.
(2) Measure the resistance between overdrive solenoid valve
terminals 1 and 2.
Resistance value: 2.7
− 3.4 Ω [at 20°C (68°F)]
Q: Is the measured resistance 2.7
− 3.4 Ω [at 20°C (68°F)?
YES : Replace the harness wire between A/T control
solenoid valve assembly connector B-02 and the
solenoid valves.
NO : Replace the overdrive solenoid valve. Refer to
GROUP 23B, Valve Body
AC202437
6
10
4
9
5
3
8
2
7
1
CONNECTOR:B-02
AB
B-02 (B)
TRANSMISSION
CONTROL CABLE
AC001968AJ
B-02 HARNESS CONNECTOR:
A/T CONTROL SOLENOID SIDE
AC004272AS
2
1
CONNECTOR : B-02-3
2
1
AC201141BM
B-02-3 HARNESS CONNECTOR :
OVERDRIVE SOLENOID
VALVE SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст