Mitsubishi Montero Sport (2004+). Manual — part 339
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-769
STEP 4. Using scan tool MB991958, check actuator test.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following items in the actuator test. Refer to
Actuator Test Reference Table
a. Item 10: EGR Vacuum Regulator Solenoid Valve.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the actuator operating properly?
YES : Go to Step 5.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
STEP 5. Using scan tool MB991958, check data list item 45:
Idle Air Control Position.
(1) Start the engine and run at idle.
(2) Set scan tool MB991958 to the data reading mode for item
45, Idle Air Control Position.
a. The idle air control motor should drop to the 0
− 2 posi-
tion during deceleration (from 1,000 r/min or more).
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the actuator operation properly?
YES : Check the following items, and repair, replace, clean
or adjust the defective sections.
a. Check the ignition coil, spark plugs, spark plug
cables.
b. Refer to On-vehicle Service - Check the
throttle valve area
Then confirm that the malfunction symptom is
eliminated.
NO : Refer to, GROUP 23A, Automatic Transaxle
Diagnosis
− Diagnostic Trouble Code Chart
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-770
INSPECTION PROCEDURE 15: Hesitation, sag or stumble.
.
COMMENT
• In cases such as the above, the ignition system,
air/fuel mixture or compression pressure may be
defective.
.
TROUBLESHOOTING HINTS (The most likely
causes for this case: )
• Malfunction of the ignition system.
• Malfunction of air/fuel ratio control system.
• Malfunction of the fuel supply system.
• Malfunction of the EGR vacuum regulator sole-
noid valve system.
• Poor compression pressure.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I
• MB991827: USB Cable
• MB991911: Main Harness B
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC set?
YES : Refer to Diagnostic Trouble Code Chart
NO : Go to Step 2.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-771
STEP 2. Using scan tool MB991958, check actuator test
items 01, 02, 03, 04, 05, 06: Injector.
(1) Check following items in the actuator test. Refer to Actuator
Test Reference Table
a. Item 01, 02, 03, 04, 05, 06: Injector.
(2) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the actuator operating properly?
YES : Go to Step 3.
NO : Refer to DTC P0201, P0202, P0203, P0204, P0205,
P0206
− Injector Circuit
.
STEP 3. Check the ignition timing.
Refer to GROUP 11A, On-vehicle Service
− Ignition Timing
Check
Q: Is the ignition timing normal?
YES : Go to Step 4.
NO : Check that the crankshaft position sensor and timing
belt cover are in the correct position. Then confirm
that the malfunction symptom is eliminated.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-772
STEP 4. Using scan tool MB991958, check data list and
actuator test.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check the following items in the data list. Refer to Data List
Reference Table
a. Item 13: Intake Air Temperature Sensor.
b. Item 25: Barometric pressure Sensor.
c. Item 21: Engine Coolant Temperature Sensor.
d. Item 14: Throttle Position Sensor.
e. Item 69: Right Bank Heated Oxygen Sensor (rear)
f. Item 39: Right Bank Heated Oxygen Sensor (front)
g. Item 59: Left Bank Heated Oxygen Sensor (rear)
h. Item 11: Left Bank Heated Oxygen Sensor (front)
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are they operating properly?
YES : Go to Step 5.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
STEP 5. Using scan tool MB991958, check actuator test.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following items in the actuator test. Refer to
Actuator Test Reference Table
a. Item 10: EGR Vacuum Regulator Solenoid Valve.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the actuator operating properly?
YES : Go to Step 6.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AK303629AB
MB991911
MB991827
MB991824
16-PIN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст