Mitsubishi Montero Sport (2004+). Manual — part 489
52A-1
GROUP 52A
INTERIOR
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .
SEAT BELT DIAGNOSIS. . . . . . . . . .
INTRODUCTION TO SEAT BELT WARNING SYSTEM
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . .
SEAT BELT WARNING SYSTEM DIAGNOSTIC
TROUBLESHOOTING STRATEGY . . . . . .
DIAGNOSIS FUNCTION. . . . . . . . . . . . . . .
SYMPTOM CHART. . . . . . . . . . . . . . . . . . .
SYMPTOM PROCEDURES . . . . . . . . . . . .
COMPASS AND TEMPERATURE DISPLAY
DIAGNOSIS . . . . . . . . . . . . . . . . . . . .
INTRODUCTION TO COMPASS AND
TEMPERATURE DISPLAY DIAGNOSIS . .
COMPASS AND TEMPERATURE DISPLAY
DIAGNOSTIC TROUBLESHOOTING
STRATEGY. . . . . . . . . . . . . . . . . . . . . . . . .
SYMPTOM CHART. . . . . . . . . . . . . . . . . . .
SYMPTOM PROCEDURES . . . . . . . . . . . .
ON-VEHICLE SERVICE . . . . . . . . . . .
PROCEDURES FOR CALIBRATING
THE COMPASS . . . . . . . . . . . . . . . . . . . . .
PROCESSES FOR ADJUSTING
THE COMPASS VARIANCE . . . . . . . . . . . .
AUTO-DIMMING FEATURE TEST . . . . . . .
SPECIAL TOOLS . . . . . . . . . . . . . . . .
INSTRUMENT PANEL ASSEMBLY* .
REMOVAL AND INSTALLATION . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
FLOOR CONSOLE ASSEMBLY . . . .
REMOVAL AND INSTALLATION . . . . . . . .
TRIMS . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
Continued on next page
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING
•
Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to
personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and
passenger (from rendering the SRS inoperative).
•
Service or maintenance of any SRS component or SRS-related component must be performed only at an
authorized MITSUBISHI dealer.
•
MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B - Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any
SRS-related component.
NOTE
The SRS includes the following components: SRS air bag control unit, SRS warning light, front impact sensors, air bag module,
clock spring, and interconnecting wiring. Other SRS-related components (that may have to be removed/installed in connection
with SRS service or maintenance) are indicated in the table of contents by an asterisk (*).
52A-2
HEADLINING . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSIDE REAR VIEW MIRROR. . . . . .
REMOVAL SERVICE POINT . . . . . . . . . . .
FRONT SEAT ASSEMBLY . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION . . . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
REAR SEAT ASSEMBLY . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . . . . .
FRONT SEAT BELT . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
REAR SEAT BELT . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . .
FASTENER TIGHTENING
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS . . . . . . . . . . .
GENERAL DESCRIPTION
TSB Revision
INTERIOR
52A-3
GENERAL DESCRIPTION
M1521000100117
OPERATION
.
Seat belt warning system
• When the ignition switch is turned "ON," the deci-
sion circuit operates and the seat belt warning
light inside of the combination meter flashes four
times for 6 seconds.
• The decision circuit output makes the seat belt
tone alarm sound intermittently for 6 seconds to
indicate unfastening of the seat belt.
• When the seat belt is buckled (seat belt buckle
switch is turned "OFF"), the seat belt tone alarm
stops sounding.
When the ignition switch is turned "OFF," both
seat belt warning light and tone alarm do not
operate.
.
Inside rear view mirror with compass and
temperature display
• The compass or temperature will appear on the
upper right of the mirror when the switch at the
center of the inside rear view mirror is pressed.
• The compass detects the vehicle direction with
the geomagnetic sensor built in the inside rear
view mirror, and displays eight directions with the
LCD.
• The outside temperature meter calculates the
information from the outside thermo sensor, and
displays the temperature with the LCD.
INSIDE REAR VIEW MIRROR WITH COMPASS AND TEMPERATURE DISPLAY
CONSTRUCTION DIAGRAM
AC003225
GEOMAGNETIC SENSOR
OUTSIDE THERMO SENSOR
AC
COMPASS DISPLAY
TEMPERATURE DISSPLAY
SEAT BELT DIAGNOSIS
TSB Revision
INTERIOR
52A-4
SEAT BELT DIAGNOSIS
INTRODUCTION TO SEAT BELT WARNING SYSTEM DIAGNOSIS
M1523003700062
The seat belt warning system is controlled by the
ETACS-ECU.
The seat belt warning system flashes the seat belt
warning light in the combination meter for 6 seconds
after the ignition switch is turned "ON," and sounds a
seat belt tone alarm if the seat belt is not fastened.
If one of the following symptoms occurs, a malfunc-
tion may have occurred.
• The seat belt warning light does not flicker even
when the ignition switch is turned "ON."
• The seat belt tone alarm does not sound even
when the ignition switch is turned "ON" while the
seat belt is not fastened.
• The seat belt tone alarm does not sound even
when the seat belt is fastened within 6 seconds
after the seat belt tone alarm starts sounding.
SEAT BELT WARNING SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1523002700069
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
fault of the seat belt warning system.
1. Gather information about the problem from the
customer.
2. Verify that the condition described by the cus-
tomer exists.
3. If you cannot verify the condition, the malfunction
is intermittent. Refer to GROUP 00, How to Cope
With Intermittent Malfunctions
.
4. Find the malfunction by following the Symptom
Chart.
DIAGNOSIS FUNCTION
M1523002800022
HOW TO CONNECT SCAN TOOL (MUT-III)
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A (Vehicles with CAN
communication system) (Vehicles with CAN communi-
cation system)
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст