Mitsubishi Montero Sport (2004+). Manual — part 276
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-517
STEP 7. Pressure test the evaporative emission system
lines between hoses E to hose L and the fuel tank.
(1) Disconnect hose E from the canister side, and plug the
hose.
(2) Remove the fuel cap.
(3) Connect the evaporative emission system pressure pump
to the fuel filler neck.
(4) Apply a pressure on the evaporative emission system
pressure pump, and confirm that air is maintained.
NOTE: The "Pressure test" in this procedure refers to the
I/M240 Simulation Test. The eight steps of this test are
described in the manufacturer's instructions for the evapo-
rative emission system pressure pump, Miller number
6872A.
(5) Disconnect the evaporative emission system pressure
pump, and reinstall the fuel cap.
(6) Connect hose E to the evaporator line.
Q: Is the evaporative emission system line free of leaks?
YES : Go to Step 15 .
NO : Go to Step 8 .
STEP 8. Check for vacuum leak in evaporative emission
system hose E.
Perform a leakage test with a hand vacuum pump on hose E.
Q: Does the hose E hold vacuum?
YES : Go to Step 9 .
NO : Replace the damaged hose. Then go to Step 16 .
AC005140
HOSE E
AC
ACX01358
AC004932
HOSE E
AH
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-518
STEP 9. Pressure test the evaporative emission system
lines between hoses F and J.
(1) Remove the fuel filler neck protector. (Refer to GROUP
13B, Fuel Tank
(2) Perform a leakage test with a hand vacuum pump on hoses
F, G, H, I and J.
Q: Do the hoses hold vacuum?
YES : Go to Step 10 .
NO : Replace the damaged hose and reinstall the fuel filler
neck protector. (Refer to GROUP 13B, Fuel Tank
STEP 10. Check the check valve A.
(1) Check valve A is a one-way check valve.
(2) Check valve A should allow air to flow in only one direction.
Q: Does check valve A allow air to press in one direction
only?
YES : Go to Step 11 .
NO : Replace it, and reinstall the fuel tank filler neck
protector. (Refer to GROUP 13B, Fuel Tank
).
Then go to Step 16 .
STEP 11. Check the check valve B.
(1) Check valve B is a one-way check valve.
(2) Check valve B should allow air to flow in only one direction.
Q: Does check valve B allow air to press in one direction
only?
YES : Go to Step 12 .
NO : Replace it, reinstall the fuel filler neck protector.
(Refer to GROUP 13B, Fuel Tank
). Then go
to Step 16 .
AC004933AD
HOSE I
HOSE G
HOSE H
HOSE J
HOSE F
AC002076 AB
CHECK VALVE A
AC002078
CHECK VALVE B
AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-519
STEP 12. Check for leaks in the evaporative emission
system hose K and L.
(1) Remove the fuel tank. (Refer to GROUP 13B, Fuel Tank
).
(2) Perform a leakage test with a hand vacuum pump on hose
k and L.
Q: Do the hoses hold vacuum?
YES : Go to Step 13 .
NO : Replace the damaged hose, and reinstall the fuel
tank. (Refer to GROUP 13B, Fuel Tank
Then go to Step 16 .
STEP 13. Check for leaks in the fuel tank.
(1) Visually check for cracks and leaks, etc.
NOTE: Carefully check the fuel pump assembly and the
inner pressure sensor installation section in the fuel tank.
AC004930
HOSE K
HOSE L
AC
AC005139
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-520
(2) Connect the evaporative emission system pressure pump
to the filler hose.
(3) Plug the fuel pump feed nipple, return hose, hose K and
hose L connected to the fuel tank.
NOTE: If these items are not securely plugged here, the
fuel could leak in the next step.
(4) Apply pressure with the evaporative emission system
pressure pump.
(5) Pressurize the fuel tank with the evaporative emission
system pressure pump.
(6) In the pressurized state, check for the leaks by applying
soapy water solution to each section and look for bubbles.
Q: Are any leaks found?
YES <When there is a leak from the attachment points of
the fuel pump assembly, the fuel tank differential
pressure sensor or the fuel tank rollover valve.> :
Reassemble the leaked parts and check again that
there are no leaks. Then reinstall the fuel tank (Refer
to GROUP 13B, Fuel Tank
). Then go to Step
16 .
YES <When there is a leak from the fuel tank.> : Replace
the fuel tank (Refer to GROUP 13B, Fuel Tank
NO : When there is no leak, reinstall the fuel tank (Refer to
GROUP 13B, Fuel Tank
). Then go to Step 14
AC005138
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст