Mitsubishi Montero Sport (2004+). Manual — part 109
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-31
STEP 13. Check the harness wire between auto-cruise
control vacuum pump connector A-02 (terminal No.2. 3
and 4) and auto-cruise control-ECU connector C-35
(terminal No.7, 8 and 16).
Q: Is any harness wire between auto-cruise control
vacuum pump connector A-02 (terminal No.2. 3 and 4)
and auto-cruise control-ECU connector C-35 (terminal
No.7, 8 and 16) damaged?
YES : Repair or replace the harness wire. Then go to Step
19 .
NO : Go to Step18 .
AC202156
3
1 2
4
CONNECTOR:A-02
HYDRAULIC
UNIT
AB
A-02:HARNESS SIDE
CONNECTOR
A-02 (B)
AC202155
2
3
10
11
5
6
13
14
12
4
8
16 15
7
9
1
C-35 (B)
AB
CONNECTOR: C-35
C-35 HARNESS SIDE
CONNECTOR
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-32
STEP 14. Measure the output circuit voltage at auto-cruise
control-ECU connector C-35 by backprobing.
(1) Do not disconnect auto-cruise control-ECU connector C-35.
(2) Turn the ignition switch to the "ON" position and the
auto-cruise control main switch to the "ON" position.
(3) Measure the voltage between auto-cruise control-ECU
connector C-35 terminal 5 and ground by backprobing.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is measured voltage approximately battery positive
voltage?
YES : Go to Step 15 .
NO : Go to Step 17 .
STEP 15. Check intermediate connector C-41 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is any connector damaged?
YES : Repair or replace the damaged components. (Refer
to GROUP 00E, Harness Connector Inspection
NO : Go to Step 16 .
AC202155
2
3
10
11
5
6
13
14
12
4
8
16 15
7
9
1
C-35 (B)
AB
CONNECTOR: C-35
C-35 HARNESS SIDE
CONNECTOR
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
ACX01899 AH
C-35 HARNESS CONNECTOR:
HARNESS SIDE
AC202075
22
2021
10
9
8
1718
6 7
19
1415
4 5
1112
1 2 3
13
16
CONNECTOR: C-41
AB
C-41
C-41: MALE SIDE CONNECTOR
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-33
STEP 16. Check the harness wire between auto-cruise
control-ECU connector C-35 (terminal No.5) and stoplight
switch connector C-66 (terminal No. 4).
Q: Is any harness wire between auto-cruise control-ECU
connector C-35 (terminal No.5) and stoplight switch
connector C-66 (terminal No. 4) damaged?
YES : Repair or replace the harness wire. Then go to Step
18 .
NO : Go to Step17 .
STEP 17. Check auto-cruise control-ECU connector C-35
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is the connector damaged?
YES : Repair or replace the damage connector. (Refer to
GROUP 00E, Harness Connector Inspection
NO : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
).
STEP 18. Check the diagnostic trouble codes.
Q: Is DTC 14 set?
YES : Replace the auto-cruise control-ECU (Refer to
). Then go to Step 19 .
NO : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
).
AC202156
3
1 2
4
CONNECTOR:A-02
HYDRAULIC
UNIT
AB
A-02:HARNESS SIDE
CONNECTOR
A-02 (B)
AC202155
2
3
10
11
5
6
13
14
12
4
8
16 15
7
9
1
C-35 (B)
AB
CONNECTOR: C-35
C-35 HARNESS SIDE
CONNECTOR
AC202155
2
3
10
11
5
6
13
14
12
4
8
16 15
7
9
1
C-35 (B)
AB
CONNECTOR: C-35
C-35 HARNESS SIDE
CONNECTOR
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-34
STEP 19. Check the diagnostic trouble codes.
Q: Is DTC 14 set?
YES : Return to Step 1 .
NO : This procedure is complete.
DTC15 : Auto-cruise Control Switch System
Auto-cruise Control Switch System Circuit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст