Mitsubishi Montero Sport (2004+). Manual — part 668
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-237
STEP 11. Check A/T control solenoid valve assembly
connector B-02, PCM connector C-92 and intermediate
connector C-96 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
AC202437
6
10
4
9
5
3
8
2
7
1
CONNECTOR:B-02
AB
B-02 (B)
TRANSMISSION
CONTROL CABLE
AC202317
PCM
120
107
119
106
129 130
118
105
117
114115116
126127128
104
111
103
112
108
101102
109110
121122123
124
113
125
CONNECTOR: C-92
C-92 (GR)
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-238
Q: Are the connectors and terminals in good condition?
YES : Go to Step 12.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC202318
22
9 10
20
19
6 7 8
21
17
1516
5
14
1213
3
2
4
18
11
1
AB
CONNECTOR: C-96
C-96
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-239
STEP 12. Check the harness for an open or short circuit to
ground between A/T control solenoid valve assembly
connector B-02 (terminals 6 and 7) and PCM connector
C-92 (terminals 107 and 129).
Q: Are the harness wires in good condition?
YES : Go to Step 13.
NO : Repair or replace the harness wire(s).
AC202437
6
10
4
9
5
3
8
2
7
1
CONNECTOR:B-02
AB
B-02 (B)
TRANSMISSION
CONTROL CABLE
AC202317
PCM
120
107
119
106
129 130
118
105
117
114115116
126127128
104
111
103
112
108
101102
109110
121122123
124
113
125
CONNECTOR: C-92
C-92 (GR)
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-240
STEP 13. Check the harness for an open or short circuit to
ground between A/T control solenoid valve assembly
connector B-02 (terminals 6, 7 and 10) and solenoid valve
connectors B-02-4 and B-02-5.
Q: Is the harness wire in good condition?
YES : Replace the PCM.
NO : Replace the harness wire.
DTC 32 (P0758): Underdrive Solenoid Valve System
.
SOLENOID VALVE SYSTEM CIRCUIT
Refer to
.
CIRCUIT OPERATION
Refer to
.
DESCRIPTIONS OF MONITOR METHODS
If solenoid terminal voltage is below specified value
when shift control is not in progress, PCM judges
that underdrive solenoid has a failure.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• DTC 41 (P0731): 1st gear incorrect ratio
• DTC 42 (P0732): 2nd gear incorrect ratio
• DTC 43 (P0733): 3rd gear incorrect ratio
• DTC 44 (P0734): 4th gear incorrect ratio
• DTC 46 (P0736): Reverse gear incorrect ratio
• DTC 36 (P0743): Torque converter clutch sole-
noid malfunction
• DTC 31 (P0753): Low-reverse solenoid malfunc-
tion
• DTC 33 (P0763): Second solenoid malfunction
• DTC 34 (P0768): Overdrive solenoid malfunction
• DTC 54 (P1751): A/T control relay malfunction
Sensor (The sensor below is determined to be
normal)
• Torque converter clutch solenoid
• Low-reverse solenoid
• Second solenoid
• Overdrive solenoid
• A/T control relay
.
AC202437
6
10
4
9
5
3
8
2
7
1
CONNECTOR:B-02
AB
B-02 (B)
TRANSMISSION
CONTROL CABLE
AC004272AO
2
1
CONNECTORS : B-02-4, B-02-5
B-02-4
B-02-5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст