Mitsubishi Montero Sport (2004+). Manual — part 655
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-185
STEP 4. Measure the switch output voltage at PCM
connector C-92 by backprobing. ("P" position)
(1) Do not disconnect connector C-92.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 101 and ground by
backprobing.
• When transmission range is "P", voltage should mea-
sure battery positive voltage.
• When transmission range is "R", voltage should mea-
sure 0.5 volt or less.
• When transmission range is "N", voltage should mea-
sure 0.5 volt or less.
• When transmission range is "D", voltage should mea-
sure 0.5 volt or less.
• When transmission range is "3", voltage should mea-
sure 0.5 volt or less.
• When transmission range is "2", voltage should mea-
sure 0.5 volt or less.
• When transmission range is "L", voltage should mea-
sure 0.5 volt or less.
Q: Is the measured voltage within the specified range?
YES : Go to Step 9.
NO : Turn the ignition switch to the "LOCK" (OFF) position.
Go to Step 5.
AC202317
PCM
120
107
119
106
129 130
118
105
117
114115116
126127128
104
111
103
112
108
101102
109110
121122123
124
113
125
CONNECTOR: C-92
C-92 (GR)
AB
AC001903AK
C-92 HARNESS CONNECTOR:
HARNESS SIDE
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-186
STEP 5. Check intermediate connector C-96 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 6.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC202318
22
9 10
20
19
6 7 8
21
17
1516
5
14
1213
3
2
4
18
11
1
AB
CONNECTOR: C-96
C-96
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-187
STEP 6. Check harness for open circuit or short circuit to
ground between transmission range switch connector
B-01 terminal 1 and PCM connector C-92 terminal 101.
Q: Is the harness wire in good condition?
YES : Go to Step 7.
NO : Repair or replace the harness wire.
AC202393
4
9
5
10
3
8
2
7
6
1
CONNECTOR: B-01
<RWD>
<4WD>
B-01 (B)
B-01 (B)
AB
AC202317
PCM
120
107
119
106
129 130
118
105
117
114115116
126127128
104
111
103
112
108
101102
109110
121122123
124
113
125
CONNECTOR: C-92
C-92 (GR)
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-188
STEP 7. Check intermediate connector C-30 and
combination meter connector C-03 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC103770
4
3
10 11
9
8
5
12
1
6
2
7
49
48
50
46
45
44
41 42 43
47
CONNECTORS: C-03, C-30
C-30
C-03
C-30
C-03
AB
AC202394
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст