Mitsubishi Montero Sport (2004+). Manual — part 1
80A-1
GROUP 80A
CONFIGURATION
DIAGRAMS
CONTENTS
OVERALL CONFIGURATION
DIAGRAM. . . . . . . . . . . . . . . . . . . . . .
HOW TO READ CONFIGURATION
DIAGRAMS . . . . . . . . . . . . . . . . . . . .
ENGINE COMPARTMENT. . . . . . . . .
TRANSMISSION . . . . . . . . . . . . . . . .
DASH PANEL . . . . . . . . . . . . . . . . . . .
JUNCTION BLOCK AND STEERING
COLUMN. . . . . . . . . . . . . . . . . . . . . . .
FLOOR AND ROOF . . . . . . . . . . . . . .
DOOR . . . . . . . . . . . . . . . . . . . . . . . . .
OVERALL CONFIGURATION DIAGRAM
TSB Revision
CONFIGURATION DIAGRAMS
80A-2
OVERALL CONFIGURATION DIAGRAM
M1801000100428
NOTE:
.
1. This illustration shows only major wiring harnesses.
2. *: also equipped at the right side.
AC002402 AC
FRONT WIRING
HARNESS
INJECTION
WIRING HARNESS
BODY WIRING
HARNESS
INSTRUMENT PANEL
WIRING HARNESS
ROOF WIRING
HARNESS
LIFTGATE
WIRING
HARNESS
FRAME WIRING
HARNESS
FLOOR WIRING
HARNESS
REAR DOOR
WIRING
HARNESS (LH)*
FRONT DOOR
WIRING HARNESS
(DRIVER'S SIDE)*
TRANSMISSION
WIRING HARNESS
POSITIVE BATTERY
CABLE
NEGATIVE BATTERY
CABLE
HOW TO READ CONFIGURATION DIAGRAMS
TSB Revision
CONFIGURATION DIAGRAMS
80A-3
HOW TO READ CONFIGURATION DIAGRAMS
M1801000200339
The wiring harness diagrams clearly show the connector locations and harness routings at each site on
actual vehicles.
AC002715
Denotes connector No.
The same connector No. is used throughout the circuit diagrams to facilitate connector location searches.
The first alphabetical symbol indicates the location site of the connector and a number that follows is the unique number.
Numbers are usually assigned to parts in clockwise order on the diagram.
Example: A-19
Number specific to connector (serial number)
Connector location site symbol
A: ENGINE COMPARTMENT
E: FLOOR AND ROOF
B: TRANSMISSION
F: DOOR
C: DASH PANEL
G: LIFTGATE
D: JUNCTION BLOCK AND
STEERING COLUMN
Denotes ground point.
Same ground number is used throughout circuit
diagrams to facilitate search of ground point.
Refer to GROUP 70 SINGLE PART INSTALLATION
POSITION - GROUND MOUNTING LOCATIONS
for details of ground points.
Denotes the color of harness outer
tube (If not specified, it is black.)
R: Red
Y: Yellow
The number of connector pins and the connector color
(except milk white)* are shown for ease of retrieval.
Example: (2-B)
Connector color
(milk white if no color is indicated)
Number of connector pins
*: Typical connector colors
B: Black
BR: Brown
Y: Yellow
V: Violet
L: Blue
O: Orange
G: Green
GR: Gray
R: Red
NONE: Milk white
A-16 (1) HORN (LOW)
A-17 (3-B) FRONT COMBONATION
LIGHT (RH)
A-18 (2-B) FRONT IMPACT SENSOR (RH)
A-19 (7-BR) VOLUME AIR FLOW SENSOR
Indicates the device to which the
connector is connected.
AD
A-17
A-16
A-18
A-19
Y
Denotes a section covered by a
corrugated tube.
The mark shows the
standard mounting position
of wiring harness.
Denotes harness name.
FRONT
WIRING
HARNESS
ENGINE COMPARTMENT
TSB Revision
CONFIGURATION DIAGRAMS
80A-4
ENGINE COMPARTMENT
M1801000300831
AC305386
AC305386
Connector
symbol
-01
thru
-47
A
AB
A-07
A-41
A-27
A-44
A-40
A-43
A-42
Y
A-04
A-02
A-01
A-36
A-35
A-32
A-21
A-31
A-08
A-05
A-06
GROUND
CABLE
1
FRONT
WIRING
HARNESS
A-01
(7-B)
VOLUME AIRFLOW SENSOR
A-02
(4-B)
AUTO-CRUISE VACUUM PUMP
A-04
(8-B)
FRONT WIRING HARNESS AND
INJECTION WIRING HARNESS
COMBINATION
A-05
(6-B)
IGNITION POWER TRANSISTOR
A-06
(3-B)
IGNITION POWER TRANSISTOR
A-07
(4-B)
RIGHT BANK HEATED OXYGEN
SENSOR (FRONT)
A-08
(1-B)
ENGINE COOLANT TEMPERATURE
GAUGE UNIT
A-09
(4-GR)
LEFT BANK HEATED OXYGEN
SENSOR (FRONT)
A-10
(2-B)
EVAPORATIVE EMISSION PURGE
SOLENOID
A-11
(2-BR)
EGR SOLENOID
A-12
(3-B)
MANIFOLD DIFFERENTIAL
PRESSURE SENSOR
A-15
(4)
WINDSHIELD WIPER MOTOR
A-17
(10-B)
FRONT WIRING HARNESS AND A/C
WIRING HARNESS COMBINATION
A-18
(2-B)
WHEEL SPEED SENSOR (FRONT:
LH) <ABS>
A-20
(2-Y)
FRONT IMPACT SENSOR (LH)
A-21
(2-B)
WINDSHIELD WASHER MOTOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст