Mitsubishi Montero Sport (2004+). Manual — part 466
DOOR
TSB Revision
BODY
42-119
STEP 6. Check the front door switch.
(1) Remove the driver's door or fornt passenger’s door switch
(Refer to
(2) Follow the table to check the front door switches continuity.
TYPE1
TYPE2
Q: Is the front door switch in good condition?
YES : Go to Step 7 .
NO : Replace front door switch, then go to Step 11.
STEP 7. Check ETACS-ECU connector D-11 and D-26 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are ETACS-ECU connector D-11 and D-26 in good
condition?
YES : Go to step 8.
NO : Repair or replace the damaged components. Refer to
GROUP 00E
, Harness Connector inspection.
Then go to Step 11.
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Released (ON)
1
− 2, 1 − 3, 2 − 3 Less than 2 ohms
Depressed (OFF) 1
− 2, 1 − 3, 2 − 3 Open circuit
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Released (ON)
1
− 2
Less than 2 ohms
Depressed (OFF) 1
− 2
Open circuit
AC003906
TYPE 1
AB
1
2
3
OFF
ON
STROKE
AC003907
TYPE 2
1
2
ON
OFF
STROKE
AB
AC202080
1
4 3 2
5
7 6
8
9
11
12
10
21
22
28 27
24
30
25
31
32
26
29
23
JUNCTION BLOCK (REAR)
CONNECTOR: D-11, D-26
D-11
D-26 (B)
D-11 COMPONENT SIDE
D-26 COMPONENT SIDE
AC
DOOR
TSB Revision
BODY
42-120
STEP 8. Check the harness wire between ETACS-ECU
connector D-11 (terminal No.9), D-26 (terminal No.26) and
driver's door switch connectors E-33 (terminal No.2), front
passenger’s side door switch connector E-46 (terminal
No.2).
AC202081
1
4 3 2
5
7 6
8
9
11
12
10
21
22
28 27
24
30
25
31
32
26
29
23
1
8
3
4
5
7 6
10
15
16
14
12
13
11
9
2
JUNCTION BLOCK (REAR)
CONNECTORS: D-11, D-14, D-26
D-11
D-26 (B)
D-11 COMPONENT SIDE
D-26 COMPONENT SIDE
AB
D-14 COMPONENT SIDE
D-14 (B)
AC202082
2 1
8
19
7
6
5
16
15
17 18
4
3
2
10 11 12 13
1
9
14
E-46
E-33
CONNECTORS: E-33, E-42, E-46
E-33, E-46 COMPONENT SIDE
E-42
E-42
AB
DOOR
TSB Revision
BODY
42-121
NOTE: After inspecting junction block connector D-14 and
intermediate connector E-42 inspect the wire. If junction block
connector D-14 or intermediate connector E-42 is damaged,
repair or replace it. Refer to GROUP 00E
, Harness
Connector Inspection. Then go to Step 11.
Q: Are there any damaged harness wires between
ETACS-ECU connector D-11 (terminal No.9), D-26
(terminal No.23) and driver's door switch connectors
E-33 (terminal No.2), front passenger’s side door switch
connector E-46 (terminal No.2)?
YES : Repair or replace the harness wire, then go to Step11.
NO : Replace the ETACS-ECU and then go to Step11.
STEP 9. Check ETACS-ECU connector D-11 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector D-11 good condition?
YES : Go to Step 10.
NO : Repair or replace the damaged components. Refer to
GROUP 00E
, Harness Connector
inspection.Then go to Step 11.
STEP 10. Check the harness wire between ETACS-ECU
connector D-11 (terminal No.3) and ignition switch.
AC201084
JUNCTION
BLOCK (REAR)
D-11
COMPONENT SIDE
AB
CONNECTOR: D-11
AC201941
M
3
1
4
2
CONNECTORS: D-08, D-11
AC
D-11
D-08
D-08 COMPONENT SIDE
D-11 COMPONENT SIDE
DOOR
TSB Revision
BODY
42-122
NOTE: After inspecting junction block connector D-08 inspect
the wire. If junction block connector D-08 is damaged, repair or
replace it. Refer to GROUP 00E
, Harness Connector
Inspection. Then go to Step 11.
Q: Are ETACS-ECU connector D-11 and ignition switch in
good condition?
YES : Replace the ETACS-ECU and then go to step 11.
NO : Repair or replace the harness wire. Refer to GROUP
, Harness Connector inspection. Then go
to Step 11.
STEP 11. Retest the system.
Q: Does the power window timer function operate
normally?
YES : The procedure is complete.
NO : Return to Step 1.
DOOR DIAGNOSIS
INTRODUCTION TO GLASS AND DOOR DIAGNOSIS
M1423007300207
Glass and door faults include water leaks and
improper opening and closing. Causes for these
faults can include faults in the glass, weatherstrip,
drain hole, waterproof film or door installation.
GLASS AND DOOR DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1423006700202
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
glass and door fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the Symptom
Chart.
4. Verify that the malfunction is eliminated.
SYMPTOM CHART
M1423007000228
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE PAGE
Water leak through door window glass
1
Door window malfunction
2
Water leak through door edge
3
Water leak from door center
4
Door hard to open
5
Door does not open or close completely.
6
Uneven gap between body
7
Wind noise around door
8
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст