Mitsubishi Montero Sport (2004+). Manual — part 461
DOOR
TSB Revision
BODY
42-99
STEP 7. Measure the power window relay supply circuit at
power window relay connector C-75X.
(1) Remove the power window relay, and measure at power
window relay connector C-75X (relay box side).
(2) Measure the resistance between terminal 2 and ground.
Q: Is the measured resistance less than 2 ohms?
YES : Go to Step 9.
NO : Go to Step 8.
STEP 8. Check the harness wire between power window
relay connector C-75X (terminal No.2) and ground.
Q: Is the harness wire damaged?
YES : Repair or replace the harness wire, then go to Step
14.
NO : Go to Step 14.
STEP 9. Check power window main switch connector F-05
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace the damaged components. Refer to
GROUP 00E
, Harness Connector inspection.
Then go to Step 14.
AC202074
4
2 1
3
CONNECTOR: C-75X
AB
C-75X
COMPONENT
SIDE
1
2
3
4
AC005050
C-75X
HARNESS CONNECTOR:
COMPONENT SIDE
AC
AC202074
4
2 1
3
CONNECTOR: C-75X
AB
C-75X
COMPONENT
SIDE
AC202003
1
7
2
8
10
11
5
13
6
14
12
4
9
3
CONNECTOR: F-05
AB
COMPONENT SIDE
FRONT
DOOR (LH)
F-05
DOOR
TSB Revision
BODY
42-100
STEP 10. Check the power supply circuit [power window
relay] at power window main switch connector F-05.
(1) Disconnect power window main switch connector F-05, and
measure at the harness side.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 13 and ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Does the measured voltage correspond with this range?
YES : Go to Step 12.
NO : Go to Step 11.
STEP 11. Check the harness wire between power window
relay connector C-75X (terminal No.1) and power window
main switch connector F-05 (terminal No.13).
AC202003
1
7
2
8
10
11
5
13
6
14
12
4
9
3
CONNECTOR: F-05
AB
COMPONENT SIDE
FRONT
DOOR (LH)
F-05
5 4
6
13
3 2 1
14
12 1110 9
8 7
AC005056AC
F-05 HARNESS CONNECTOR:
COMPONENT SIDE
AC202074
4
2 1
3
CONNECTOR: C-75X
AB
C-75X
COMPONENT
SIDE
AC202003
1
7
2
8
10
11
5
13
6
14
12
4
9
3
CONNECTOR: F-05
AB
COMPONENT SIDE
FRONT
DOOR (LH)
F-05
DOOR
TSB Revision
BODY
42-101
NOTE: After inspecting intermediate connector C-40 inspect
the wires. If intermediate connector C-40 is damaged, repair or
replace it. Refer to GROUP 00E
, Harness Connector
Inspection. Then go to Step 14.
Q: Is the harness wire damaged?
YES : Repair or replace the harness wire, then go to Step
14.
NO : Go to Step 14.
STEP 12. Measure the power window main switch ground
circuit at power window main switch connector F-05.
(1) Disconnect power window main switch connector F-05, and
measure at the harness side.
(2) Measure the resistance between terminal 12 and ground.
Q: Is the measured resistance less than 2 ohms?
YES : Replace the power window main switch then go to
Step 14.
NO : Go to Step 13.
STEP 13. Check the harness wire between power window
main switch connector F-05 (terminal No.12) and ground.
AC309309AF
C-40
CONNECTOR: C-40
AC202003
1
7
2
8
10
11
5
13
6
14
12
4
9
3
CONNECTOR: F-05
AB
COMPONENT SIDE
FRONT
DOOR (LH)
F-05
5 4
6
13
3 2 1
14
12 1110 9
8 7
AC005057
F-05 HARNESS CONNECTOR:
COMPONENT SIDE
AC
AC202003
1
7
2
8
10
11
5
13
6
14
12
4
9
3
CONNECTOR: F-05
AB
COMPONENT SIDE
FRONT
DOOR (LH)
F-05
DOOR
TSB Revision
BODY
42-102
NOTE: After inspecting intermediate connector C-40 inspect
the wires. If intermediate connector C-40 is damaged, repair or
replace it. Refer to GROUP 00E
, Harness Connector
Inspection. Then go to Step 14.
Q: Is the harness wire damaged?
YES : Repair or replace the harness wire, then go to Step
14.
NO : Go to Step 14.
STEP 14. Retest the system.
Q: Does the power window function operate normally?
YES : The procedure is complete.
NO : Return to Step 1.
AC309309AF
C-40
CONNECTOR: C-40
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст