Mitsubishi Montero Sport (2004+). Manual — part 665
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-225
.
AC202437
6
10
4
9
5
3
8
2
7
1
CONNECTOR:B-02
AB
B-02 (B)
TRANSMISSION
CONTROL CABLE
AC004272AM
2
1
CONNECTORS : B-02-1, B-02-2, B-02-3
B-02-4, B-02-5
B-02-1
B-02-2
B-02-3
B-02-4
B-02-5
AC202439
22
2021
10
9
8
1718
6 7
19
1415
4 5
1112
1 2 3
13
16
22
9 10
20
19
6 7 8
21
17
1516
5
14
12 13
3
2
4
18
11
1
CONNECTORS: C-41, C-96
AB
C-41
C-96
C-41
C-96
AC202317
PCM
120
107
119
106
129 130
118
105
117
114115116
126127128
104
111
103
112
108
101102
109110
121122123
124
113
125
CONNECTOR: C-92
C-92 (GR)
AB
AC202440
1
3 4
2
CONNECTOR: C-97
AB
C-97
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-226
CIRCUIT OPERATION
• The A/T control relay supplies battery positive
voltage to the solenoid valve assembly (terminals
9 and 10).
• The solenoid valve closes when energized (on),
and opens when not energized (off). The PCM
energizes the solenoid valve based on input data
from sensors such as the TP Sensor, Transmis-
sion Range Switch, Stoplight Switch, Vehicle
Speed Sensor, Input Shaft Speed Sensor, Output
Shaft Speed Sensor, and Transmission Fluid
Temperature Sensor.
• The PCM provides the ground to energize the
solenoid. The amount of time that the circuit is
grounded is displayed on scan tool MB991958 in
percent.
• When the solenoid is energized or de-energized,
fluid passes through the valve body and transmis-
sion passages to apply and release components.
.
DESCRIPTIONS OF MONITOR METHODS
If solenoid terminal voltage is below specified value
when shift control is not in progress, PCM judges
that low-reverse solenoid has a failure.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• DTC 41 (P0731): 1st gear incorrect ratio
• DTC 42 (P0732): 2nd gear incorrect ratio
• DTC 43 (P0733): 3rd gear incorrect ratio
• DTC 44 (P0734): 4th gear incorrect ratio
• DTC 46 (P0736): Reverse gear incorrect ratio
• DTC 36 (P0743): Torque converter clutch sole-
noid malfunction
• DTC 32 (P0758): Underdrive solenoid malfunc-
tion
• DTC 33 (P0763): Second solenoid malfunction
• DTC 34 (P0768): Overdrive solenoid malfunction
• DTC 54 (P1751): A/T control relay malfunction
Sensor (The sensor below is determined to be
normal)
• Torque converter clutch solenoid
• Underdrive solenoid
• Second solenoid
• Overdrive solenoid
• A/T control relay
.
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-227
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
Check Conditions
• Solenoid status: either solid ON or OFF.
• Shift status: in-gear.
• Voltage of battery: 10 volts or more.
Judgement Criteria
• Solenoid voltage: 3 volts or less. (0.3 second)
• If DTC 31 (P0753) is set consecutively four times,
the transmission is locked into 3rd gear as a
fail-safe measure, and the "N" range light flashes
once per second.
.
OBD-II DRIVE CYCLE PATTERN
Start the engine, and keep the vehicle stopped in P
range for 5 seconds.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Malfunction of low-reverse solenoid valve
• Damaged harness, connector
• Malfunction of the PCM
AC205281
Good
Malfunction
END
START
In-gear?
Shift solenoid-A is in ON
or OFF steady state
Voltage of battery > 10 V
Solenoid circuit
voltage < 3 V
Continuous failure
for 0.3 sec.
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Low-reverse solenoid valve
is in ON or OFF steady state
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
TSB Revision
AUTOMATIC TRANSMISSION
23A-228
DIAGNOSIS
Required Special Tool:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
STEP 1. Using scan tool MB991958, check actuator test
item 01: Low-Reverse Solenoid Valve.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to actuator test mode.
• Item 01: Low-Reverse Solenoid Valve.
• An audible clicking or buzzing should be heard when
the low-reverse solenoid valve is energized.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the solenoid valve operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст