Mitsubishi Montero (2002-2004). Manual — part 893
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-55
STEP 8. Check the harness for open circuit or damage
between input shaft speed sensor connector C-16 terminal
2 and PCM connector D-134 terminal 64.
Q: Is the harness wire in good condition?
YES : Go to Step 19.
NO : Repair or replace the harness wire.
AC204747
CONNECTOR : C-16
C-16 (B)
AB
1
3
2
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-56
STEP 9. Check input shaft speed sensor connector C-16,
PCM connector D-134 and intermediate connector E-114
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 10.
NO : Repair or replace the damages components. Refer to
GROUP 00E, Harness Connector Inspection
AC204747
CONNECTOR : C-16
C-16 (B)
AB
1
3
2
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-57
STEP 10. Check the harness for short circuit to ground
between input shaft speed sensor connector C-16 terminal
2 and PCM connector D-134 terminal 64.
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair or replace the harness wire.
AC204747
CONNECTOR : C-16
C-16 (B)
AB
1
3
2
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-58
STEP 11. Measure the ground circuit for resistance at the
input shaft speed sensor connector C-16.
(1) Disconnect connector C-16 from the speed sensor and
measure at the harness side.
(2) Measure the resistance between terminal 1 and ground.
• The resistance should measure less than 2 ohms.
Q: Is the measured resistance less than 2 ohms?
YES : Go to Step 16.
NO : Go to Step 12.
AC204747
CONNECTOR : C-16
C-16 (B)
AB
1
3
2
AC204918
3
1
2
AC204918
C-16 HARNESS CONNECTOR :
COMPONENT SIDE
DE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст