Mitsubishi Montero (2002-2004). Manual — part 320
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-327
STEP 7. Check the wiring harness between taillight (LH)
connector G-16 (terminal 1) and front-ECU connector A-
07X (terminal 8).
AC204183
CONNECTOR : A-07X
AB
2 1
3
4
6
7
8
9
5
11 10
RELAY BOX SIDE
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-328
NOTE: Also check intermediate connectors D-28, D-111 and F-
10 for loose, corroded, or damaged terminals, or terminals
pushed back in the connector. If intermediate connector D-28,
D-111 or F-10 is damaged, repair or replace the damaged com-
ponent(s) as described in GROUP 00E, Harness Connector
Inspection
.
Q: Is the wiring harness between taillight (LH) connector
G-16 (terminal 1) and front-ECU connector A-07X
(terminal 8) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillight (RH) and side marker light (RH)
illuminates normally.
AC204170
CONNECTOR : D-28
AI
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC204171
CONNECTOR : D-111
AC
9
8
6 7
5
3 4
20
32
21
33
43
17 18
30
41
16
29
28
39 40
13
25
12
24
35 36
14
26
37
15
27
38
19
31
42
1
10
22
2
11
23
34
AC204178
CONNECTOR : F-10
AD
F-10(GR)
F-10(GR)
3
1
2
4
5
6
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-329
STEP 8. Check the ground circuit to the position light (LH).
Test at position light (LH) connector A-18.
(1) Disconnect position light (LH) connector A-18 and measure
the resistance available at the wiring harness side of the
connector.
(2) Measure the resistance value between terminal 1 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : No action is necessary and testing is complete.
NO : Go to Step 9.
STEP 9. Check position light (LH) connector A-18 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is position light (LH) connector A-18 in good condition?
YES : Go to Step 10.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the position light illuminates
normally.
STEP 10. Check the wiring harness between position light
(LH) connector A-18 (terminal 1) and ground.
Q: Is the wiring harness between position light (LH)
connector A-18 (terminal 1) and ground in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the position light illuminates normally.
AC204167
CONNECTOR : A-18
HARNESS
SIDE
A-18(GR)
A-18(GR)
AG
2 1
AC100264
2 1
AB
CONNECTOR A-18
(HARNESS SIDE)
AC204167
CONNECTOR : A-18
HARNESS
SIDE
A-18(GR)
A-18(GR)
AG
2 1
AC204167
CONNECTOR : A-18
HARNESS
SIDE
A-18(GR)
A-18(GR)
AG
2 1
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-330
STEP 11. Check the position light bulb (LH).
(1) Remove the position light bulb (LH).
(2) Verify that the position light bulb (LH) is not damaged or
burned out.
Q: Is the position light bulb (LH) in good condition?
YES : Go to Step 12.
NO : Replace the position light bulb (LH). Verify that the
position light (LH) illuminates normally.
STEP 12. Check the ground circuit to the position light
(LH). Test at position light (LH) connector A-18.
(1) Disconnect position light (LH) connector A-18 and measure
the resistance available at the wiring harness side of the
connector.
(2) Measure the resistance value between terminal 1 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 15.
NO : Go to Step 13.
STEP 13. Check position light (LH) connector A-18 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is position light (LH) connector A-18 in good condition?
YES : Go to Step 14.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the position light (LH) illuminates
normally.
AC204167
CONNECTOR : A-18
HARNESS
SIDE
A-18(GR)
A-18(GR)
AG
2 1
AC100264
2 1
AB
CONNECTOR A-18
(HARNESS SIDE)
AC204167
CONNECTOR : A-18
HARNESS
SIDE
A-18(GR)
A-18(GR)
AG
2 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст