Mitsubishi Montero (2002-2004). Manual — part 279
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-163
STEP 9. Check at front power window sub-switch (RH)
connector H-16 in order to check the ground circuit to the
front power window sub-switch (RH).
(1) Disconnect front power window sub-switch (RH) connector
H-16, and measure at the harness side.
(2) Measure the resistance value between terminal 4 and
ground.
• The resistance should measure 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 13.
NO : Go to Step 10.
STEP 10. Check power window main switch connector H-
05 and front power window sub-switch (RH) connector H-
16 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are power window main switch connector H-05 and
front power window sub-switch (RH) connector H-16 in
good condition?
YES : Go to Step 11.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the front power window sub-
switch (RH) should now work normally.
AC000238
CONNECTOR: H-16
H-16
AF
H-16
(HARNESS SIDE)
AC204323AB
CONNECTOR: H-16
(HARNESS SIDE)
1
2
3
4
5
6
7
8
9
10
AC203774
CONNECTOR: H-05
AE
DRIVER'S DOOR
H-05
H-05
AC000238
CONNECTOR: H-16
H-16
AE
H-16
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-164
STEP 11. Check the harness wiring between power window
main switch connector H-05 (terminal 14) and front power
window sub-switch (RH) connector H-16 (terminal 4).
AC203774
CONNECTOR: H-05
AF
DRIVER'S DOOR
H-05
H-05
(HARNESS SIDE)
AC000238
CONNECTOR: H-16
H-16
AF
H-16
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-165
NOTE: Also check intermediate connectors D-25 and D-15. If
intermediate connectors D-25 or D-15 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the harness wiring between power window main
switch connector H-05 (terminal 14) and front power
window sub-switch (RH) connector H-16 (terminal 4) in
good condition?
YES : Go to Step 12.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the front power window sub-switch (RH) should now
work normally.
AC203859 AC
CONNECTOR: D-25
D-25
D-25
AC203860 AB
D-15
D-15
CONNECTOR: D-15
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-166
STEP 12. Check the harness wiring between power
window main switch connector H-05 (terminal 1) and front
power window sub-switch (RH) connector H-16 (terminal
10).
AC203774
CONNECTOR: H-05
AF
DRIVER'S DOOR
H-05
H-05
(HARNESS SIDE)
AC000238
CONNECTOR: H-16
H-16
AF
H-16
(HARNESS SIDE)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст