Mitsubishi Montero (2002-2004). Manual — part 962
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-331
STEP 4. Check joint connector A-15, free-wheel engage
solenoid valve connectors A-38, A-39, intermediate
connector D-28, junction block connector D-210 and D-208
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
AC204167
CONNECTOR : A-15
AU
1213
4 5
14
10
3
8 9
2
7
1
6
11
AC204184
CONNECTORS : A-38, A-39
A-38 (B)
A-39 (BR)
AD
A-38
2
1
A-39
2
1
AC204170
CONNECTOR : D-28
CH
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-332
Q: Are the connectors and terminals in good condition?
YES : Go to Step 5.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204191
CONNECTORS : D-208, D-210
D-208
D-208
D-210
D-210
AP
5 6
2
4
3
1
5
4
12 13
3
2
9
7 8
10
6
1
11
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-333
STEP 5. Check harness for open circuit or short circuit to
ground between free-wheel engage solenoid valve
connectors A-38, A-39 terminal 1 and junction block
connector D-208 terminal 2.
Q: Is the harness wire in good condition?
YES : Go to Step 10.
NO : Repair or replace the harness wire.
AC204184
CONNECTORS : A-38, A-39
A-38 (B)
A-39 (BR)
AD
A-38
2
1
A-39
2
1
AC204173
CONNECTOR : D-208
BA
5 6
2
4
3
1
JUNCTION BLOCK
(FRONT VIEW)
DIAGNOSTIC TROUBLE CODE PROCEDURES <TRANSFER>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-334
STEP 6. Measure the solenoid valve output voltage at the
transfer-ECU connector E-104 by backprobing.
(1) Do not disconnect connector E-104.
(2) Turn the ignition switch to the "ON" position.
(3) Transmission range should be "N" range.
(4) Measure the voltage between terminal 41 and ground by
backprobing.
• When the transfer shift lever position is other than 2H,
voltage should measure battery positive voltage.
• When the transfer shift lever position is 2H, voltage
should measure less than 1.0 volt.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage normal?
YES : Go to Step 9.
NO : Go to Step 7.
AC204176
CONNECTOR : E-104
BA
51
40
3839
50
41
52
48
37
46
35
47
36
45
34
43
32
44
33
49
42
31
AC204918 BW
E-104 HARNESS CONNECTOR :
HARNESS SIDE
51
40
3839
50
41
52
48
37
46
35
47
36
45
34
43
32
44
33
49
42
31
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст